- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- Trunk o LACP
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
12-12-2017 09:38 AM
12-12-2017 09:38 AM
Trunk o LACP
Ciao a tutti,
ho una granconfusione riguardo a trunk e LACP ed avrei bisogno il vostro aiuto.
Attualmente ho configurato due HP 2920 con ultimo firmware Aruba, messi in stack tra di loro con apposito modulo.
Successivamente mi sono messo a configurare dei trunk che vanno verso firewall e virtualconnect di server enclosure ma da qua sono iniziati i problemi.
Attualmente i trunk che ho creato lato switch sono tutti con da immagine allegata.
Se però provo a cambiare la tipologia dei trunk, come attivi ricevo degli errori, qui sotto le modalità possibili:
LACP Status:
disable
active
passive
Trunk Type:
none
trunk
lacp
Potete aiutarmi a capire come configurare questi trunk? Ho letto su internet e l'idea che mi sono fatto è che aggrego porte con il trunk e poi all'interno dovrei mettere da un lato (es switch) LACP Attivo e dell'altro (es virtual connect del server) LACP passivo.
Alcuni invece parlano di LACP dinamico.
Help!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
12-12-2017 10:55 AM
12-12-2017 10:55 AM
Re: Trunk o LACP
Ciao, sarebbe meglio scrivere in inglese (se ti è possibile) in modo che tutta la HPE Community possa intervenire (l'inglese è la lingua franca).
Ad ogni modo provo a risponderti io (se vuoi mandami un PM): l'idea è giusta ma la terminologia può portarti fuori strada...Port Trunking è l'aggregazione di più (n>=2 e generalmente n<8) interfacce (dette anche porte) fisiche come membri dell'interfaccia logica chiamata Trunk...poi tale interfaccia può essere configurata in modalità Trunk (di qui la confusione) ovvero "non protocol" (senza protocollo) oppure LACP ovvero "protocollo IEEE 802.3ad".
Generalmente si usa configurare Port Trunking con l'interfaccia logica Trunk di tipo LACP (che, in alcuni contesti, può essere chiamata Dynamic o IEEE 802.3ad)...poi a sua volta si sceglie Attivo in entrambi i lati (lato Server e lato Switch se i link fisici iniziano e terminano tra questi oppure lato Switch e lato Switch se i link iniziano e terminano tra due Switches).
Se hai uno Stack di Aruba 2920 (WB.16.04.xxxx) puoi creare un Port Trunking con, ad esempio, membri le porte 1/A1 e 2/A1 - così usi porte uguali di membri dello Stack diversi per aumentare la resilienza in caso di problemi ad uno dei due Switch in Stack - oppure le porte 1/A1 ed 1/A2 (del solo membro 1 dello Stack)...se solo lì hai tali porte a disposizione (penso 10G su modulo posteriore)...fatto questo selezioni LACP e scegli Attivo...lato Server devi fare bonding (o teaming) con le stesse caratteristiche (due porte, stesse velocità, stesso Full-Duplex, stesso LACP, stesso stato Attivo).
Fare Port Trunking con 1 porta non ha senso.
Davide.
I'm not an HPE Employee

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
12-13-2017 03:10 AM
12-13-2017 03:10 AM
Re: Trunk o LACP
Grazie 1000 per la risposta mi hai già chiarito dei dubbi!
Ovviamente sullo switch ho fatto dei Port Trunk con due porte, come suggerivi tu ho fatto port trunk di due porte a 10GB.
Per cui ho un port trunk, il tipo di trunk è LACP, quando provo a cambiarlo in attivo mi seganal questo errore:
Dynamic LACP can not be activated in a manual trunk port
Cosa sbaglio? Il trunk una volta fatto non si può modificare? Devo eliminarlo e ricrearlo?
Altra indicazione, le porte nel trunk le ho messe tutte in auto, meglio impostare la velocità e il full-duplex?
Grazie anticipatamente per l'aiuto
Ciao
Angelo
___________________________________________________
Thanks 1000 for the answer you have already clarified the doubts!
Obviously on the switch I made Port Trunks with two ports, as you suggested I did port port of two 10GB ports.
So I have a trunk port, the type of trunk is LACP, when I try to change it in the active I seganal this error:
Dynamic LACP can not be activated in a manual trunk port
What am I doing wrong? The trunk once done can not be changed? Do I have to delete it and recreate it?
Another indication, the ports in the trunk I put them all in the car, better set the speed and full-duplex?
Thanks in advance for the help
Hello
Angel
Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP