- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- Re: VLAN Tagging not working between HP 3500YL and...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-01-2016 10:49 PM - edited 06-01-2016 10:52 PM
06-01-2016 10:49 PM - edited 06-01-2016 10:52 PM
VLAN Tagging not working between HP 3500YL and Cisco 2950
Hi HP experts,
I have been stuck at a migration from Cisco to HP vlan tagging issue. I have port Fa0/2 on tagged (trunk) and connects to HP 3500 on its port 7. The configuration are there but somehow multiple vlans don't pass over connection between Cisco 2950 & HP 3500. Only 1 vlan passes at a time. All vlans are allowed on trunk /tagged link on Cisco side. 802.1q tagging is encapsulated in cisco 2950. Below is the configuration for Cisco and HP
Cisco 2950
Int f0/0
description ***connection to router***
Switchport mode trunk.
Int f0/2
Description ***Connection to HP-3500***
Switchport mode trunk
vlan 112
ip add 192.168.112.161 255.255.255.0
vlan 113
interface vlan 113
ip address 192.168.113.161 255.255.255.0
---------------------------------------------
HP-3500 CONFIG
int vlan 112
tagged 7
ip add 192.168.112.1/24
int vlan 113
ip add 192.168.113.1/24
tagged 7
vlan 1
untagged 7
I can't ping Cisco 2950 interface vlan 192.168.112.161 from HP 192.168.112.1 when untagged vlan 1 (native vlan), but when native vlan changed to 112 (vlan 112--->untagged 7) I can ping 192.168.112.1 but can't ping 192.168.113.1. If I remove untagged 1 and put untagged 7 for vlan 113 then I can ping 192.168.113.161 from HP but failed to ping 192.168.112.161. So it carries only 1 vlan at a time.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-02-2016 01:19 PM
06-02-2016 01:19 PM
Re: VLAN Tagging not working between HP 3500YL and Cisco 2950
switchport switchport trunk encapsulation dot1q switchport mode trunk switchport trunk native vlan 1 switchport trunk allowed vlan all switchport nonegotiate
On cisco, try interface commands above.
Moreover, what is output on Cisco of commands
show vlan
show interfaces trunk