Aruba & ProVision-based
cancel
Showing results for 
Search instead for 
Did you mean: 

Voice VLAN help please

 
Huggiesbear-78
Occasional Contributor

Voice VLAN help please

Hello all
I am a novice to switches but I know the basics. I am trying to setup my switch to allow my IP phone to connect to my Voice network VLAN 30 and my PC to connect to the same port via the PC port on my IP phone VLAN 1.

I have setup my VLAN’s and the access port has VLAN 1 untagged and VLAN 30 tagged. I have a scope on my Windows 2012 server DHCP for both my default and voice VLAN. My switch is a 2930 48 port and my router is a Cisco RV 320. On the voice VLAN I have DHCP Relay set to go to my Windows Server on VLAN 1 and in the voice scope I have the Mitel phone string in option 43 and I also tried Mitel vendor option 125.

On the router
Port 1 VLAN 1 untagged VLAN 30 tagged
Port 4 VLAN 30 untagged VLAN 1 tagged
inter networking enables

VLAN 1 DHCP Windows server 192.168.1.10
VLAN 30 DHCP RELAY to above

Switch port to router for VLAN 1 untagged
Switch port to router for VLAN 30 untagged

Device port VLAN 30 tagged for phone and VLAN 1 untagged to pc connecting via phone

Does this all sound right?
Do I need a dhcp relay on the vlans?
Should the device port be an access or trunk?
Should LLDP / LLDP-MED be used or not essential?

Any other points will be helpful as it’s been two weeks trying now and not any further lol. I can draw a simple diagram if needed
2 REPLIES 2
vladi0782
Advisor

Re: Voice VLAN help please

Does your configuration using static IP addresses work well?

Can you reach your default gateway on both networks?

Switch port to router for VLAN 1 untagged
Switch port to router for VLAN 30 tagged

vlan 1
name "DEFAULT_VLAN"
untagged 1-48
exit
vlan 30
name "Telefonia_IP"
tagged 1-48
no ip address
exit

Be happy for this moment. This moment is your life
parnassus
Honored Contributor

Re: Voice VLAN help please


@vladi0782 wrote:

 

vlan 1
name "DEFAULT_VLAN"
untagged 1-48
exit
vlan 30
name "Telefonia_IP"
tagged 1-48
no ip address
exit


I would add voice to VLAN 30 (if VLAN 30 is the Voice dedicated VLAN):

vlan 1
 name "DEFAULT_VLAN"
 untagged 1-48
 exit
vlan 30
 voice
 name "Telefonia_IP"
 tagged 1-48
 no ip address
exit

What I don't understand is the untagging/tagging pattern you described for your Router ports:

Port 1 VLAN 1 untagged VLAN 30 tagged
Port 4 VLAN 30 untagged VLAN 1 tagged

IMHO if you would just use one uplink between your Switch and your Router thus - considering only port 1 of the Cisco RV320 - it should be:

Port 1 VLAN 1 untagged VLAN 30 tagged

Or, alternativley, if you really have two separate physical uplinks (one for each VLAN Id) to your Cisco RV320, then it should eventually be:

Port 1 VLAN 1 untagged
Port 4 VLAN 30 untagged

Switch side...these two possible scenarios will lead to mutually exclusive:

  • One uplink port untagged member of VLAN 1 (data) and, concurrently, tagged member of VLAN 30 (voice)
  • Two uplink ports:
    • The 1st uplink to Port 1 of Cisco RV320: untagged member of VLAN 1 (data)
    • The 2nd uplink to Port 4 of Cisco RV320: untagged member of VLAN 30 (voice)