- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Aruba & ProVision-based
- >
- Where is the conf-command "job" on HPE/Aruba Serie...
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
07-11-2016 04:47 AM - edited 07-11-2016 04:48 AM
07-11-2016 04:47 AM - edited 07-11-2016 04:48 AM
Where is the conf-command "job" on HPE/Aruba Series Switches
Hey there,
in the following PDF we've read, that there is a possibility to schedule a job, e. g. deactivate poe at night and enable it at the morning: http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=c04777645 (Page 128-130)
Does this feature depend on a special firmware? The "job" command isn't available at our HP 54xx/82xx Series Switches.
Thanks in advance for a reply.
Best regards,
Hungryduck
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
07-11-2016 05:37 AM - edited 07-11-2016 06:59 AM
07-11-2016 05:37 AM - edited 07-11-2016 06:59 AM
Re: Where is the conf-command "job" on HPE/Aruba Series Switches
Silly question: are you typing that job command at Global Configuration level (the prompt will be like HP Switch(config)# )?
Eventually, which switch exact model and product number you're speaking about (probably you're referring to 5400 zl / 8200 zl Switch Series) and what software version is it actually running?
Edit: ouch...I didn't noticed the OP's Thread Title (...conf-command...)...it's self-explanatory...so probably you aren't in the right privilege level to execute that command (job)...see Chapter 3 "Using the Command Line Interface (CLI)" starting from page 25 of the same document you referred to.
I'm not an HPE Employee

Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP