- Community Home
- >
- Storage
- >
- Legacy
- >
- Automated Backup
- >
- 1/8 Tape Autoloader 230 and 29160LP
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-02-2004 09:51 PM
тАО12-02-2004 09:51 PM
1/8 Tape Autoloader 230 and 29160LP
I have searched the forums but am a bit confused
Is anyone able to tell me if the two peices of hardware above will work together?
We have a tape autoloader and this card but it doesnt seem to detect, we have changed scsi ids, rebooted, tried the card in different systems and nothing.
many thanks
adam
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-03-2004 02:46 AM
тАО12-03-2004 02:46 AM
Re: 1/8 Tape Autoloader 230 and 29160LP
boot in the bios of the HBA with Ctrl_A
press f6 for default setting,
check for bent pin or damaged cable/terminator
check for disconnected cables inside the autoloader
If everything is under control, you are going too slow (Mario Andretti)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-08-2004 01:58 AM
тАО12-08-2004 01:58 AM
Re: 1/8 Tape Autoloader 230 and 29160LP
Ive checked and reset the scsi device id and reset it to defaults, practically tried everything! changed scsi ids on the tape auto loader, screwed about with the settings
I brought an old apaptec 2940UW scsi card in from home and hooked it up and changed the scsi id of the scsi controller and it detected it and showed up!
Only difference is i can see between the two cards is the connector on the scsi card. I have attached an image of the convertor cable we had to buy seperately to connect the two devices.
The smaller connector on the cable is the whats going into the scsi card.
I have attached an image with pictures of the scsi card and cable i am working with. sorry if the pictures are a bit crappy, camera isnt exactly the best in the world.
The card is going into a standard PCI bus and not a picx slot. dont know if that effects this or not.
Really baffled me to why it wont work. any other suggestions would help
Thanks
Adam
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-29-2004 10:56 PM
тАО12-29-2004 10:56 PM
Re: 1/8 Tape Autoloader 230 and 29160LP
I had a similar problem with the Autoloader, in the end I brought a new SCSI Card 'HP 64-bit/133-MHz pci-x dual channel ultra320 host bus adapter', cost around ├В┬г200. P/N 268351-B21. I also I had to get a new SCSI cable to convert from wide 63pin to small 64pin P/N 341176-B21.
Hope this helps you.
Let me know how it goes
D
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-03-2005 08:01 PM
тАО01-03-2005 08:01 PM
Re: 1/8 Tape Autoloader 230 and 29160LP
unless anyone else can shed any light on this i think its sorted
thanks all for your replys
adam