- Community Home
- >
- Storage
- >
- Legacy
- >
- Automated Backup
- >
- Re: DL380 and Storageworks1/8
Automated Backup
1753388
Members
6930
Online
108792
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-30-2003 06:41 PM
06-30-2003 06:41 PM
DL380 and Storageworks1/8
I purchased a HP Proliant DL380 and Storageworks autoloader 1/8. The server will recognize the device at boot, if I use the onboard SCSI. However, it does not support multiple LUNs (Unless there is a patch available) I have tried installing an additional adaptec controller (2940UW Pro), but it fails on the scsi scan. Running Netware 6. Anybody have a solution this trio?
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-01-2003 07:04 PM
07-01-2003 07:04 PM
Re: DL380 and Storageworks1/8
Doug.
This is apparently an issue with the SCSI card being configured for using "Multi LUNs".
I am reliably informed this is turned off by default in the 29XX series from Adaptec.
First thing to check, on boot enter the SCSI card config and scan for devices. You should see both the SCSI ID and the LUN.
If you only see the SCSI ID of the tape device, reconfigure the card until both are present.
Secondly check for the Std SCSI ID conflicts etc.
All should work on the HW as described.
Good Luck.
Trevor.
This is apparently an issue with the SCSI card being configured for using "Multi LUNs".
I am reliably informed this is turned off by default in the 29XX series from Adaptec.
First thing to check, on boot enter the SCSI card config and scan for devices. You should see both the SCSI ID and the LUN.
If you only see the SCSI ID of the tape device, reconfigure the card until both are present.
Secondly check for the Std SCSI ID conflicts etc.
All should work on the HW as described.
Good Luck.
Trevor.
Baldric, I have a plan so cunning you could pin a tail on it and call it a weasle.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP