- Community Home
- >
- Storage
- >
- Legacy
- >
- Automated Backup
- >
- HP SureStore DAT24x6e
Automated Backup
1753886
Members
7616
Online
108809
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-14-2004 07:11 AM
06-14-2004 07:11 AM
HP SureStore DAT24x6e
Hi,
This DAT24x6e powers up and immediately enters a state in which all three LEDs flash rapidly. The LCD briefly reads "Self Test" and then reads "SCSI ID: 6" There are no error messages on the LCD. This condition occurs with or without the drive connected to the SCSI controller.
Interestingly enough, this drive was working fine initially. It was then powered down for rougly eight weeks and when it was turned back on manifest this condition.
I can find no information regarding this condition. Any help will be greatly appriciated.
Chris
This DAT24x6e powers up and immediately enters a state in which all three LEDs flash rapidly. The LCD briefly reads "Self Test" and then reads "SCSI ID: 6" There are no error messages on the LCD. This condition occurs with or without the drive connected to the SCSI controller.
Interestingly enough, this drive was working fine initially. It was then powered down for rougly eight weeks and when it was turned back on manifest this condition.
I can find no information regarding this condition. Any help will be greatly appriciated.
Chris
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-15-2004 11:02 AM
06-15-2004 11:02 AM
Re: HP SureStore DAT24x6e
Hi Chris,
I hope you can found the solution on this nice document
http://h10025.www1.hp.com/ewfrf/wc/genericDocument?lc=en&cc=us&docname=c00048372
marino
I hope you can found the solution on this nice document
http://h10025.www1.hp.com/ewfrf/wc/genericDocument?lc=en&cc=us&docname=c00048372
marino
---------------X-------------------X--------------------X----------------X--------------
If everything is under control, you are going too slow (Mario Andretti)
If everything is under control, you are going too slow (Mario Andretti)
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP