- Community Home
- >
- Storage
- >
- Legacy
- >
- Automated Backup
- >
- LT892 on Windows 2003
Automated Backup
1753907
Members
8501
Online
108810
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-24-2005 02:15 AM
03-24-2005 02:15 AM
LT892 on Windows 2003
Hello all,
I have a LT892 with 2 DLT7000 drives.
I work on HP ML570 G2 under Win2003.
The library and the 2 drives are connected on the same SCSI chain plugged on a SMART Array 5300 ( see document attached ).
The ID SCSI : 4=Library, 5=DLT0, 6=DLT1.
When a boot the server on the post of the SMART Array the 2 drives are detected but not the Library. And when the system is up, I can see the 2 drives but not the library and I can use it the my backup software.
First question : Normaly did I must see the librairy dectection on the post of the SMART Array ?
Second question : May be I missed on step ?
Third question : How can I do to setup the library in windows. Do you have a command (Unix like) to check each SCSI component connect on the server ?
Best Regards,
CB.
I have a LT892 with 2 DLT7000 drives.
I work on HP ML570 G2 under Win2003.
The library and the 2 drives are connected on the same SCSI chain plugged on a SMART Array 5300 ( see document attached ).
The ID SCSI : 4=Library, 5=DLT0, 6=DLT1.
When a boot the server on the post of the SMART Array the 2 drives are detected but not the Library. And when the system is up, I can see the 2 drives but not the library and I can use it the my backup software.
First question : Normaly did I must see the librairy dectection on the post of the SMART Array ?
Second question : May be I missed on step ?
Third question : How can I do to setup the library in windows. Do you have a command (Unix like) to check each SCSI component connect on the server ?
Best Regards,
CB.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP