HPE Community read-only access December 15, 2018
This is a maintenance upgrade. You will be able to read articles and posts, but not post or reply.
Hours:
Dec 15, 4:00 am to 10:00 am UTC
Dec 14, 10:00 pm CST to Dec 15, 4:00 am CST
Dec 14, 8:00 pm PST to Dec 15, 2:00 am PST
BladeSystem - General
cancel
Showing results for 
Search instead for 
Did you mean: 

All blades offline in c3000

 
Swarm
Occasional Advisor

All blades offline in c3000

Hi guys,


We just had an issue in which all of our blades had a red X and status unknown in our c3000 enclosure.

OA Firmware 3.6

 

Any ideas?  Log is below

 

Jul 26 05:45:44 Kernel: hub 1-1:1.0: over-current change on port 2
Jul 26 05:45:44 Kernel: hub 1-1:1.0: over-current change on port 2
Jul 26 05:45:45 Kernel: hub 1-1:1.0: over-current change on port 2
Jul 26 05:45:45 Kernel: hub 1-1:1.0: over-current change on port 2
Jul 26 05:46:28 Kernel: Network link is up at 1000Mbps - Full Duplex
Jul 26 05:46:30 OA: Time zone changed to SGT-8
Jul 26 05:46:32 OA: LCD Status is: OK.
Jul 26 05:46:32 OA: Device 2 power delayed during device discovery.
Jul 26 05:46:33 OA: Blade in bay #2 status changed to OK
Jul 26 05:46:33 Enclosure-Link: Service started
Jul 26 05:46:40 Enclosure-Link: Initial topology scan completed successfully
Jul 26 05:46:42 OA: Device 2 power delayed until potential partner devices are discovered.
Jul 26 05:46:44 Redundancy: Service started (ACTIVE)
Jul 26 05:46:44 OA: Onboard Administrator booted successfully
Jul 26 05:46:57 OA: HTTP server is up
Jul 26 05:47:01 OA: VLAN is disabled
Jul 26 05:47:50 OA: Internal health status of interconnect in bay 1 changed to OK
Jul 26 05:49:38 OA: Management Processor on Blade 1 appears unresponsive.
Jul 26 05:49:43 OA: Partner device 2 was denied power because the corresponding device is missing.
Jul 26 05:49:56 OA: Management Processor on Blade 4 appears unresponsive.
Jul 26 05:50:20 OA: Management Processor on Blade 8 appears unresponsive.
Jul 26 05:51:52 OA: Blade 1 has been allocated a default power value of 509W because iLO appears unresponsive.
Jul 26 05:51:52 OA: Blade 4 has been allocated a default power value of 509W because iLO appears unresponsive.
Jul 26 05:51:52 OA: Blade 8 has been allocated a default power value of 509W because iLO appears unresponsive.

2 REPLIES
Torsten.
Acclaimed Contributor

Re: All blades offline in c3000

The OA cannot "see" the ILOs.

I would first check and restart the OA, then the ILOs (blades) if needed.

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Swarm
Occasional Advisor

Re: All blades offline in c3000

I did restart the OA but unfortunately this did not do anything for the blades.

 

I had to unplug the power on the enclosure, wait, then plug it back in.

 

Not sure if a newer firmware fixes this?