- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- BL20p G4 - front LED not working.
BladeSystem - General
1753507
Members
5146
Online
108795
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-30-2009 09:53 AM
тАО09-30-2009 09:53 AM
BL20p G4 - front LED not working.
Hi,
Since I did a firmware update on the blade, the whole front LED stop working. The only lights I get are the two hard drive activity. Even the power button is not lit. The blade functions correctly. Anywone seen this before?
I'm going to open up the blade to see if I've hooked a wire or something while upgrading the ram. But I thought I might post here anyways just in case someone has seen this before.
Thanks.
Since I did a firmware update on the blade, the whole front LED stop working. The only lights I get are the two hard drive activity. Even the power button is not lit. The blade functions correctly. Anywone seen this before?
I'm going to open up the blade to see if I've hooked a wire or something while upgrading the ram. But I thought I might post here anyways just in case someone has seen this before.
Thanks.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-30-2009 10:11 AM
тАО09-30-2009 10:11 AM
Re: BL20p G4 - front LED not working.
My BAD,
The thin ribon cable was out of the socket. I pushed it in a 1/4 inch and I have the LEDs back.
Was only a coincidance it was at the same time as the firmware update.
Have a great one.
The thin ribon cable was out of the socket. I pushed it in a 1/4 inch and I have the LEDs back.
Was only a coincidance it was at the same time as the firmware update.
Have a great one.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-30-2009 10:13 AM
тАО09-30-2009 10:13 AM
Re: BL20p G4 - front LED not working.
See above ^
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP