- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Bl25p G2 Memory Issue
BladeSystem - General
1753633
Members
5841
Online
108798
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-25-2008 11:00 AM
03-25-2008 11:00 AM
Bl25p G2 Memory Issue
Hi,
We just received a new blade and purchased 8 2GB (PC2-5300) memory modules for it. But I just put in the memory and try to boot the blade up but it keeps resetting itself when it gets to the checking memory screen.
Anyone have any ideas why this is happening? We have the same memory in other blades?
Thanks.
We just received a new blade and purchased 8 2GB (PC2-5300) memory modules for it. But I just put in the memory and try to boot the blade up but it keeps resetting itself when it gets to the checking memory screen.
Anyone have any ideas why this is happening? We have the same memory in other blades?
Thanks.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-25-2008 06:16 PM
03-25-2008 06:16 PM
Re: Bl25p G2 Memory Issue
Hello Eric,
I wold suggest the best way will be to try is min configuration and trying 1 pair of memory with proc 1 installed ins slot 1 and swap proc 2 in slot 1 and so also check the memory guideline :
All DIMMs must be PC2-5300 Registered DDR2 DIMMs (667 MHz.)
Both DIMM slots in a memory bank must be populated.
Both DIMMs in a memory bank must be identical.
Processor 1 memory bank A must always be populated.
DIMM banks are active only when the corresponding processor socket is populated.
If installing only one bank on a processor, populate the bank physically farthest from the processor.
If mixing DIMM sizes on the same processor, the largest capacity DIMMs must be populated in the bank physically farthest from the processor. The smallest capacity DIMMs must be populated in the bank physically nearest the processor.
For optimal performance in most applications, populate the first memory bank for every populated processor socket.
Please check the attached doc for more help and ensure that we have the latest bios firmware
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=15351&prodSeriesId=3191210&prodNameId=3288168&swEnvOID=1005&swLang=8&mode=2&taskId=135&swItem=MTX-ae8e3ab8cba94fb09ab4e10ad6
Thanks regards
Sammy :)
I wold suggest the best way will be to try is min configuration and trying 1 pair of memory with proc 1 installed ins slot 1 and swap proc 2 in slot 1 and so also check the memory guideline :
All DIMMs must be PC2-5300 Registered DDR2 DIMMs (667 MHz.)
Both DIMM slots in a memory bank must be populated.
Both DIMMs in a memory bank must be identical.
Processor 1 memory bank A must always be populated.
DIMM banks are active only when the corresponding processor socket is populated.
If installing only one bank on a processor, populate the bank physically farthest from the processor.
If mixing DIMM sizes on the same processor, the largest capacity DIMMs must be populated in the bank physically farthest from the processor. The smallest capacity DIMMs must be populated in the bank physically nearest the processor.
For optimal performance in most applications, populate the first memory bank for every populated processor socket.
Please check the attached doc for more help and ensure that we have the latest bios firmware
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=15351&prodSeriesId=3191210&prodNameId=3288168&swEnvOID=1005&swLang=8&mode=2&taskId=135&swItem=MTX-ae8e3ab8cba94fb09ab4e10ad6
Thanks regards
Sammy :)
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP