- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: C3000 enclosure network setup..
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-30-2010 09:47 PM
тАО06-30-2010 09:47 PM
C3000 enclosure network setup..
I am trying to setup networking on a HP c3000 bladeserver enclosure. It has the following h/w: 3 HP Proliant BL280c G6 Blades with 2 NIC each,1 GbE2c Layer 2/3 Ethernet Blade switch..
I have installed windows server 2008 x64 one of my blades and also we have a direct internet connection through ethernet cat 5 cable. so i want to provide the public ip assigned to us one of the NIC of blades. so i am not able to understand how to do this. i am a new guy and first time configuring the blades..and wahat is port mapping plz exp[lain as well.
thanks and regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-30-2010 10:27 PM
тАО06-30-2010 10:27 PM
Re: C3000 enclosure network setup..
Are you wanting to host something like web or mail from this blade?
If so its simply a firewall configuration step required. In its simpilest form you need to setup a NAT on the firwall to point the publid IP to the IP of the blade which hosts service you want to present to the internet.
Just make sure your blade as static IP.
Disclaimer: the NAT described above does not take into account any other security concerns or configs regarding the firewall and NAT options. :-)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-30-2010 10:29 PM
тАО06-30-2010 10:29 PM
Re: C3000 enclosure network setup..
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-30-2010 10:39 PM
тАО06-30-2010 10:39 PM
Re: C3000 enclosure network setup..
Thanks for quick reply.
actully we are hosting an exchange server 2007 in a blade, file server in another one, but in third we've installed MS forefront TMG 2010 as a firewall solution. in previous setup on TMG server there were 2 NICs one had local LAN ip and another was directly connected to the internet with public IP address. i need same setup for third blade so where should i plug the cable coming from ISP and wat else configuration i have to made.
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-30-2010 10:41 PM
тАО06-30-2010 10:41 PM
Re: C3000 enclosure network setup..
Port mapping defines these internal connections and helps you decide in placement of the Interconnect modules or the slection of the mezzanine slot in which you want to plug in a specific card in the blade.
You need to always make sure that you have the right placement of the interconnect modules and the mezzanine cards in your blade.
Please refer to the following link to find the port mapping for a C3000 enclosure( page 45 and 46). Note that the mapping differs for full height and half height blades.
http://h20000.www2.hp.com/bc/docs/support/SupportManual/c01167165/c01167165.pdf
In your case the placement of the two NICs that you have should be according to the port mapping rules.