- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Cannot access iLo from OA or directly
BladeSystem - General
1753479
Members
4867
Online
108794
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-03-2008 05:46 AM
тАО04-03-2008 05:46 AM
Cannot access iLo from OA or directly
Hi,
I recently upgraded my firmware baseline to:
-OA 2.13
-VCM 1.22
-465c A13 18/11/2007
-685c A08 17/11/2007
-iLO 1.50
All upgrades were fine and subsequent testing was successful, however a couple of days later 3/4 blades no report in OA that they cannot connect to iLO.
If I try to connect I get -> Autologin failed: The Onboard Administrator cannot communicate with iLO. Please check iLO network configuration.
I have tried to connect directly to the IP, but it just hangs.
I have also tried...
-Failing over between OA's
-Resetting the OA's
-Rebooting the affected blades
-Re-updating the EBIPA info
..without success.
I can ping the iLO IP's and the gateway on the management network.
The only thing I haven't tried (as they are at a remote data centre) is re-seating the blades, but then again other than iLO I can manage the blades in all other ways so not sure if reseating will help?
Any ideas?
Thanks
Kevin
I recently upgraded my firmware baseline to:
-OA 2.13
-VCM 1.22
-465c A13 18/11/2007
-685c A08 17/11/2007
-iLO 1.50
All upgrades were fine and subsequent testing was successful, however a couple of days later 3/4 blades no report in OA that they cannot connect to iLO.
If I try to connect I get -> Autologin failed: The Onboard Administrator cannot communicate with iLO. Please check iLO network configuration.
I have tried to connect directly to the IP, but it just hangs.
I have also tried...
-Failing over between OA's
-Resetting the OA's
-Rebooting the affected blades
-Re-updating the EBIPA info
..without success.
I can ping the iLO IP's and the gateway on the management network.
The only thing I haven't tried (as they are at a remote data centre) is re-seating the blades, but then again other than iLO I can manage the blades in all other ways so not sure if reseating will help?
Any ideas?
Thanks
Kevin
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-03-2008 06:50 AM
тАО04-03-2008 06:50 AM
Re: Cannot access iLo from OA or directly
Hi Kevin,
If you want to try reseating server from remote location you can use the below command from OA.
RESET SERVER [ ]: Reset the server bay by momentarily removing all power.
It is as good as removing and inserting a server. You will have a syslog entries which say server is being removed and inserted.
If you want to try reseating server from remote location you can use the below command from OA.
RESET SERVER [
It is as good as removing and inserting a server. You will have a syslog entries which say server is being removed and inserted.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-04-2008 03:54 AM
тАО04-04-2008 03:54 AM
Re: Cannot access iLo from OA or directly
Thanks that worked beautifully :o))
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-04-2008 06:52 AM
тАО04-04-2008 06:52 AM
Re: Cannot access iLo from OA or directly
Forum Points are appreciated :-)
Regards,
Regards,
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP