- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: Cluster with C7000
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-14-2008 09:54 AM
тАО07-14-2008 09:54 AM
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-14-2008 10:41 AM
тАО07-14-2008 10:41 AM
Re: Cluster with C7000
two cluster networks must not have a component in common that can cause both to
fail simultaneously." I believe the half-heighth blade does not fit this criteria, whereas, with the NICs correctly configured in MSCS, the full-heigth blade does.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-14-2008 05:01 PM
тАО07-14-2008 05:01 PM
Re: Cluster with C7000
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-15-2008 12:00 AM
тАО07-15-2008 12:00 AM
Re: Cluster with C7000
yes you could do that, i created the VLAN also this way however then you are not able to team the onboard NIC's (which is what you like to do) since, with only two interconnect Ethernet switches, you are not able to connect any additional network ports you from the server blades.
This is because the port mapping from the server blade mezzanine cards in mezzanine slot 1 i.e. map to the switch modules in the slots 3 and 4 in the back of the enclosure.
So either you build a hearbeat within the 2 switches you have now or you need to buy additional Ethernet switches and mezzanine cards to accomplish what you want.
As mentioned before, with the full height blades which have 4 build in network cards one can build a team and heartbeat lan with just 2 Ethernet switches because all those 4 network ports map to the first two interconnect swithes in the back of the enclosure.
Have a look here, this will make it more clear to you:
http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00816246/c00816246.pdf?jumpid=reg_R1002_USEN
figure 15 and 16 page 22
HTH
Kris
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2008 07:55 AM
тАО07-16-2008 07:55 AM
Re: Cluster with C7000
Thanks for your response. Do you think that is possible to add a new a dual ports mezzanine card in a blade server and configure those two NICs talk to blade switch 1 and 2 ? Otherwise, to buy a new blade switch just for the heartbeat connection is very pricy. But, I will go that way if I have no choice.
Thanks !
Eric Lai
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2008 11:06 AM
тАО07-16-2008 11:06 AM
Re: Cluster with C7000
NO Eric. Its not possible in C7000 enclosure.
If you have C3000 the Mezzanine 1 will map to Switch 2.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2008 11:25 AM
тАО07-16-2008 11:25 AM
SolutionUnfortunately, you can't change the internal port mapping of the C7000 enclosure.
As you can see in the attached file, the half-height server blade's (BL460c) integrated Gigabit Ethernet Adapters are mapped in a c7000 enclosure to interconnects 1 and 2 (Where you have your 2 GbE2c Ethernet Blade Switches).
If you want to add more Ethernet adapters to your configuration, you must place an interconnect on the back of the chassis that maps directly to your PCIe mezzanine card positioning. Mezzanine 1 will lead you to Interconnects 3 and 4. Mezzanine 2 will lead you to Interconnects 5, 6, 7 and 8 (depending on the type of mezzanine card used).
Since you're planning a cluster environment I suppose you have already occupied bays 3 and 4 with some sort of interconnect for Fibre Channel connectivity for your cluster's shared storage.
That will leave bays 5, 6, 7 and 8 free for more Ethernet connectivity.
If I was in your place, I would try to add 2 more switches to bays 5 and 6, and a dual-port Gigabit Ehernet mezzanine card to the second mezzanine slot on each server.
But if you're struggling with budget constraints you can always consider buying Ethernet Pass-throughs instead:
http://h18004.www1.hp.com/products/blades/components/ethernet/pass-thru/index.html
These are somewhat cheaper than Ethernet switches and give you direct port mapping to each ethernet port on your blade servers.
Hope this helps.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2008 12:03 PM
тАО07-16-2008 12:03 PM
Re: Cluster with C7000
Thanks for your suggestion. I think that is the way we will go.
Thanks for all of you again.
Eric Lai
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-17-2008 06:16 AM
тАО07-17-2008 06:16 AM
Re: Cluster with C7000
We are looking into doing something similar. My question is, what are you using as the shared storage? A storage blade or a SAN on the network?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-17-2008 10:17 AM
тАО07-17-2008 10:17 AM