- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: ILO reset
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-20-2009 10:18 AM
тАО04-20-2009 10:18 AM
ILO reset
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-20-2009 10:50 AM
тАО04-20-2009 10:50 AM
Re: ILO reset
enclosure information -> enclosure settings -> enclosure bay IP
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-20-2009 10:52 AM
тАО04-20-2009 10:52 AM
Re: ILO reset
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-20-2009 10:57 AM
тАО04-20-2009 10:57 AM
Re: ILO reset
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-20-2009 11:23 AM
тАО04-20-2009 11:23 AM
Re: ILO reset
All of the selected iLO Processors will be reset if the protocol is enabled. If each iLO has been previously given a static IP address, these EBIPA settings will not change the static IP address
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-20-2009 01:02 PM
тАО04-20-2009 01:02 PM
Re: ILO reset
But you can do it from the OS using the HPONCFG utility (downloadable as a "driver" from ilO drivers) and I think you can issue HPCONCFG commands directly in the OA CLI.
The HP ILO forum maybe best to ask the format of the command/script.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-21-2009 09:31 AM
тАО04-21-2009 09:31 AM
Re: ILO reset
However if you download HPONCFG and run it against the blade's loaded OS you can supply (or gather and modify) an XML file to change the settings. HPONCFG is already a command within the OA's command-line interface. To use it, open an SSH to the OA and type:
HPONCFG
to upload the XML via FTP/HTTP, or:
HPONCFG
then paste in your XML, then
For example:
HPONCFG 3 <<~
...paste in XML text...
~
Good luck!