- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Move vc modules in c7000 enclosure
BladeSystem - General
1752786
Members
5740
Online
108789
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-22-2010 10:04 AM
01-22-2010 10:04 AM
Move vc modules in c7000 enclosure
I have 2 flex 10 enet modules in bay 1 and 2. And 2 1/10 enet modules in bay 5 and 6. I need to swap them so a bl680c with 10g e mezzanine can use the flex 10 vc module.
I tried backing up the vc config and moving the vc modules but that did not work.
How can I accomplish this? Hopefully I don't have to reconfigure the enclosure from scratch.
Thanks
I tried backing up the vc config and moving the vc modules but that did not work.
How can I accomplish this? Hopefully I don't have to reconfigure the enclosure from scratch.
Thanks
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-22-2010 11:58 AM
01-22-2010 11:58 AM
Re: Move vc modules in c7000 enclosure
I'm not sure that this is a simple task.
I believe you can do the opposite, i.e. replace a 1/10G with a Flex10, by inporting the configuration.
However, I would expect problems because the 1/10G hass less memory than the Flex10.
I am curious: What error messages did you get (if any) when you tried to import the configuration? (I assume that this is where it failed).
What procedure exactly, did you use.
vis;
1) shutdown all the blades.
2) removed the VC modules.
3) delete them from the domain.
4) ....
etc. etc.
Dave
I believe you can do the opposite, i.e. replace a 1/10G with a Flex10, by inporting the configuration.
However, I would expect problems because the 1/10G hass less memory than the Flex10.
I am curious: What error messages did you get (if any) when you tried to import the configuration? (I assume that this is where it failed).
What procedure exactly, did you use.
vis;
1) shutdown all the blades.
2) removed the VC modules.
3) delete them from the domain.
4) ....
etc. etc.
Dave
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP