- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: Possibility of using the Blades G6 in enclosur...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-09-2010 07:10 AM
тАО02-09-2010 07:10 AM
Possibility of using the Blades G6 in enclosure generation first.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-09-2010 10:22 AM
тАО02-09-2010 10:22 AM
Re: Possibility of using the Blades G6 in enclosure generation first.
Dave.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-09-2010 11:26 PM
тАО02-09-2010 11:26 PM
Re: Possibility of using the Blades G6 in enclosure generation first.
/Magnus
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-10-2010 10:01 AM
тАО02-10-2010 10:01 AM
Re: Possibility of using the Blades G6 in enclosure generation first.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-28-2010 02:54 AM
тАО02-28-2010 02:54 AM
Re: Possibility of using the Blades G6 in enclosure generation first.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-28-2010 06:34 AM
тАО02-28-2010 06:34 AM
Re: Possibility of using the Blades G6 in enclosure generation first.
fans will go full speed thats normal wait 20 seconds reinsert the OA is all okay now ,
if not remove optional cards mezzaine etc inc extra dimms ,, from the blade and reinsert it what happens now if same issue .
clear nv ram
blade clear nvranm
Clearing the system configuration
To clear the system configuration:
1. Power down the server blade
2. Remove the server blade
3. Remove the access panellook at the diagram on it it will show the position of the maintenace switch( it clears Nv ram)
4. Change position 6 of the system maintenance switch to on.
5. Install the access panel
6. Install the server blade in the enclosure and power up the server blade.
7. Wait for the POST message that prompts you to change the switch setting:
Maintenance switch detected in the "On" position.
Power off the server and turn switch to the "Off" position.
8. Repeat steps 1 through 3.
9. Change position 6 of the system maintenance switch to off.
10. Repeat steps 5 through 7.
now if you cannot ping blade ilo request
new sys board..
This is how we thank each other in the forum
http://forums11.itrc.hp.com/service/forums/helptips.do?#33
Enjoy:)