- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: Power topology error in P class Blade enclosur...
BladeSystem - General
1753654
Members
5755
Online
108798
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-15-2008 02:22 AM
тАО03-15-2008 02:22 AM
Power topology error in P class Blade enclosure
Iam having P class Blade enclosures with Blade 20p & 25p. Iam getting error power topolgy mismatch.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-15-2008 04:57 AM
тАО03-15-2008 04:57 AM
Re: Power topology error in P class Blade enclosure
Hello,
where did you get this error? Are both power busses under voltage?? All power supplies up and running? Are you using single phase or three-phase?
Best regards,
Patrick
where did you get this error? Are both power busses under voltage?? All power supplies up and running? Are you using single phase or three-phase?
Best regards,
Patrick
Best regards,
Patrick
Patrick
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-15-2008 08:52 AM
тАО03-15-2008 08:52 AM
Re: Power topology error in P class Blade enclosure
Hi,
update the firmware of the management modules :
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=15351&prodSeriesId=327558&prodNameId=3288172&swEnvOID=1005&swLang=8&mode=2&taskId=135&swItem=MTX-e25b66dcc42a4b798fc4a7ddaa
If the error is not gone away, reset the management module, check for LEDs near the bus bars in back of the enclosures...
Have you configured any power zones?
Is this a false message or something is not functioning fine?
Pac
update the firmware of the management modules :
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=15351&prodSeriesId=327558&prodNameId=3288172&swEnvOID=1005&swLang=8&mode=2&taskId=135&swItem=MTX-e25b66dcc42a4b798fc4a7ddaa
If the error is not gone away, reset the management module, check for LEDs near the bus bars in back of the enclosures...
Have you configured any power zones?
Is this a false message or something is not functioning fine?
Pac
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP