QMH2462 can't see tape drives after library reboot. BL465c Linux AS 4 x86_64

[Moreno Daltin]

Hello

We are running Linux CentOS 4.4 on several HP BL465c. Our TL is HP ESL712. The storage is HP XP12000. The mezzanine HBA is QMH2462 and the driver is 8.01.07.25-fo

When the machines boot, they can "see" and use everything alright (i.e. XP's LUNs and ESL712's tape drives). If we reboot the TL when the machines are running, after the TL comes up they cannot access the TL's drives anymore. The backup software is data protector 5.5. Below is attached a dmesg of one of the affected systems. Whenever we have to reboot the TL we have to reboot many connected systems too, in order to have our backups working. hp_rescan doesn't help. This issue seems to be related to x86_64 installed machines only (the 32bit are not suffering of it). Any help to fix this? Thanks.


Bootdata ok (command line is ro root=LABEL=/ rhgb quiet)
Linux version 2.6.9-42.ELsmp (buildcentos@mehak.karan.org) (gcc version 3.4.6 20060404 (Red Hat 3.4.6-3)) #1 SMP Tue Aug 15 10:35:26 BST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fe50000 (usable)
BIOS-e820: 000000007fe50000 - 000000007fe58000 (ACPI data)
BIOS-e820: 000000007fe58000 - 0000000080000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fed00000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffc00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 000000087ffff000 (usable)
ACPI: RSDP (v002 HP ) @ 0x00000000000f4f00
ACPI: XSDT (v001 HP A08 0x00000002 Ò^D 0x0000162e) @ 0x000000007fe50780
ACPI: FADT (v003 HP A08 0x00000002 Ò^D 0x0000162e) @ 0x000000007fe50800
ACPI: SPCR (v001 HP SPCRRBSU 0x00000001 Ò^D 0x0000162e) @ 0x000000007fe50140
ACPI: MCFG (v001 HP ProLiant 0x00000001 0x00000000) @ 0x000000007fe501c0
ACPI: HPET (v001 HP A08 0x00000002 Ò^D 0x0000162e) @ 0x000000007fe50200
ACPI: SPMI (v005 HP ProLiant 0x00000001 Ò^D 0x0000162e) @ 0x000000007fe50240
ACPI: MADT (v001 HP 00000083 0x00000002 0x00000000) @ 0x000000007fe50280
ACPI: SRAT (v001 AMD HAMMER 0x00000001 AMD 0x00000001) @ 0x000000007fe50380
ACPI: DSDT (v001 HP DSDT 0x00000001 INTL 0x20030228) @ 0x0000000000000000
Enabling SRAT NUMA discovery
SRAT: PXM 0 -> APIC 0 -> Node 0
SRAT: PXM 0 -> APIC 1 -> Node 0
SRAT: PXM 1 -> APIC 2 -> Node 1
SRAT: PXM 1 -> APIC 3 -> Node 1
SRAT: PXM 2 -> APIC 4 -> Node 2
SRAT: PXM 2 -> APIC 5 -> Node 2
SRAT: PXM 3 -> APIC 6 -> Node 3
SRAT: PXM 3 -> APIC 7 -> Node 3
SRAT: Node 0 PXM 0 0-9ffff
SRAT: Node 0 PXM 0 0-7fffffff
SRAT: Node 0 PXM 0 0-27fffffff
SRAT: Node 1 PXM 1 280000000-47fffffff
SRAT: Node 2 PXM 2 480000000-67fffffff
SRAT: Node 3 PXM 3 680000000-87fffffff
Warning: acpi_table_parse(ACPI_SLIT) returned 0!
Using 24 for the hash shift. Max addr is 87fffffff
Bootmem setup node 0 0000000000000000-000000027fffffff
Bootmem setup node 1 0000000280000000-000000047fffffff
Bootmem setup node 2 0000000480000000-000000067fffffff
Bootmem setup node 3 0000000680000000-000000087fffefff
No mptable found.
On node 0 totalpages: 2621439
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 2617343 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
On node 1 totalpages: 2097151
DMA zone: 0 pages, LIFO batch:1
Normal zone: 2097151 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
On node 2 totalpages: 2097151
DMA zone: 0 pages, LIFO batch:1
Normal zone: 2097151 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
On node 3 totalpages: 2097150
DMA zone: 0 pages, LIFO batch:1
Normal zone: 2097150 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
Nvidia board detected. Ignoring ACPI timer override.
ACPI: PM-Timer IO Port: 0x908
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
Processor #2 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] enabled)
Processor #4 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] enabled)
Processor #6 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
Processor #3 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x05] enabled)
Processor #5 15:1 APIC version 16
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled)
Processor #7 15:1 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
Setting APIC routing to flat
ACPI: IOAPIC (id[0x08] address[0xf7df0000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 17, address 0xf7df0000, GSI 0-23
ACPI: IOAPIC (id[0x09] address[0xfddf0000] gsi_base[38])
IOAPIC[1]: apic_id 9, version 17, address 0xfddf0000, GSI 38-61
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 0 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ9 used by override.
ACPI: HPET id: 0x10228201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000)
Checking aperture...
CPU 0: aperture @ 4000000 size 32 MB
Aperture from northbridge cpu 0 too small (32 MB)
No AGP bridge found
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 4000000
Built 4 zonelists
Kernel command line: ro root=LABEL=/ rhgb quiet console=tty0
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 25.000000 MHz HPET timer.
time.c: Detected 3014.182 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 8388608 (order: 14, 67108864 bytes)
Inode-cache hash table entries: 4194304 (order: 13, 33554432 bytes)
Memory: 32892040k/35651580k available (2105k kernel code, 0k reserved, 1297k data, 196k init)
Calibrating delay using timer specific routine.. 6031.00 BogoMIPS (lpj=3015504)
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
There is already a security framework initialized, register_security failed.
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0(2) -> Node 0
Using local APIC NMI watchdog using perfctr0
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0(2) -> Node 0
CPU0: Dual-Core AMD Opteron(tm) Processor 8222 stepping 03
per-CPU timeslice cutoff: 1023.87 usecs.
task migration cache decay timeout: 2 msecs.
Booting processor 1/2 rip 6000 rsp 104800abf58
Initializing CPU#1
Calibrating delay using timer specific routine.. 6027.93 BogoMIPS (lpj=3013968)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 2(2) -> Node 2
Dual-Core AMD Opteron(tm) Processor 8222 stepping 03
Booting processor 2/4 rip 6000 rsp 104800b5f58
Initializing CPU#2
Calibrating delay using timer specific routine.. 6027.86 BogoMIPS (lpj=3013933)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 4(2) -> Node 0
Dual-Core AMD Opteron(tm) Processor 8222 stepping 03
Booting processor 3/6 rip 6000 rsp 10878f91f58
Initializing CPU#3
Calibrating delay using timer specific routine.. 6027.87 BogoMIPS (lpj=3013937)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 6(2) -> Node 2
Dual-Core AMD Opteron(tm) Processor 8222 stepping 03
Booting processor 4/1 rip 6000 rsp 10478f97f58
Initializing CPU#4
Calibrating delay using timer specific routine.. 6027.88 BogoMIPS (lpj=3013943)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1(2) -> Node 1
Dual-Core AMD Opteron(tm) Processor 8222 stepping 03
Booting processor 5/3 rip 6000 rsp 10878fb7f58
Initializing CPU#5
Calibrating delay using timer specific routine.. 6027.85 BogoMIPS (lpj=3013927)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 3(2) -> Node 3
Dual-Core AMD Opteron(tm) Processor 8222 stepping 03
Booting processor 6/5 rip 6000 rsp 10478fbdf58
Initializing CPU#6
Calibrating delay using timer specific routine.. 6027.87 BogoMIPS (lpj=3013938)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 5(2) -> Node 1
Dual-Core AMD Opteron(tm) Processor 8222 stepping 03
Booting processor 7/7 rip 6000 rsp 104800e9f58
Initializing CPU#7
Calibrating delay using timer specific routine.. 6027.84 BogoMIPS (lpj=3013923)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 7(2) -> Node 3
Dual-Core AMD Opteron(tm) Processor 8222 stepping 03
Total of 8 processors activated (48226.14 BogoMIPS).
Using local APIC timer interrupts.
Detected 12.559 MHz APIC timer.
checking TSC synchronization across 8 CPUs:
BIOS BUG: CPU#0 improperly initialized, has 11 usecs TSC skew! FIXED.
BIOS BUG: CPU#1 improperly initialized, has 4 usecs TSC skew! FIXED.
BIOS BUG: CPU#2 improperly initialized, has -3 usecs TSC skew! FIXED.
BIOS BUG: CPU#3 improperly initialized, has -13 usecs TSC skew! FIXED.
BIOS BUG: CPU#4 improperly initialized, has 13 usecs TSC skew! FIXED.
BIOS BUG: CPU#5 improperly initialized, has 4 usecs TSC skew! FIXED.
BIOS BUG: CPU#6 improperly initialized, has -3 usecs TSC skew! FIXED.
BIOS BUG: CPU#7 improperly initialized, has -13 usecs TSC skew! FIXED.
Brought up 8 CPUs
time.c: Using HPET based timekeeping.
checking if image is initramfs... it is
NET: Registered protocol family 16
PCI: Using configuration type 1
PCI: Using MMCONFIG at 80000000
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040816
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:09.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.IP2P._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE1.NB01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE2.NC1B._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.CPE3.NC2B._PRT]
ACPI: PCI Root Bridge [PCI1] (00:40)
PCI: Probing PCI hardware (bus 40)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI1.IPE2.SASB._PRT]
ACPI: PCI Interrupt Link [LNKW] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [LNKX] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [LNKY] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [LNKZ] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [LNU0] (IRQs 22) *5
ACPI: PCI Interrupt Link [LNU2] (IRQs 23) *7
ACPI: PCI Interrupt Link [LNKA] (IRQs 54) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 55) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 56) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 57) *0, disabled.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNU0] enabled at IRQ 22
GSI 16 sharing vector 0xB1 and IRQ 16
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 22 (level, high) -> IRQ 177
ACPI: PCI Interrupt Link [LNU2] enabled at IRQ 23
GSI 17 sharing vector 0xB9 and IRQ 17
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 23 (level, high) -> IRQ 185
ACPI: PCI Interrupt Link [LNKY] enabled at IRQ 18
GSI 18 sharing vector 0xC1 and IRQ 18
ACPI: PCI interrupt 0000:01:03.0[A] -> GSI 18 (level, high) -> IRQ 193
ACPI: PCI Interrupt Link [LNKW] enabled at IRQ 16
GSI 19 sharing vector 0xC9 and IRQ 19
ACPI: PCI interrupt 0000:01:04.0[A] -> GSI 16 (level, high) -> IRQ 201
ACPI: PCI Interrupt Link [LNKX] enabled at IRQ 17
GSI 20 sharing vector 0xD1 and IRQ 20
ACPI: PCI interrupt 0000:01:04.2[B] -> GSI 17 (level, high) -> IRQ 209
ACPI: PCI interrupt 0000:01:04.4[B] -> GSI 17 (level, high) -> IRQ 209
ACPI: PCI interrupt 0000:01:04.6[A] -> GSI 16 (level, high) -> IRQ 201
ACPI: PCI interrupt 0000:03:00.0[A] -> GSI 17 (level, high) -> IRQ 209
ACPI: PCI interrupt 0000:05:00.0[A] -> GSI 16 (level, high) -> IRQ 201
ACPI: PCI Interrupt Link [LNKZ] enabled at IRQ 19
GSI 21 sharing vector 0xD9 and IRQ 21
ACPI: PCI interrupt 0000:07:04.0[A] -> GSI 19 (level, high) -> IRQ 217
ACPI: PCI interrupt 0000:07:04.1[B] -> GSI 16 (level, high) -> IRQ 201
ACPI: PCI interrupt 0000:08:00.0[A] -> GSI 18 (level, high) -> IRQ 193
ACPI: PCI interrupt 0000:08:00.1[B] -> GSI 19 (level, high) -> IRQ 217
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 54
GSI 22 sharing vector 0xE1 and IRQ 22
ACPI: PCI interrupt 0000:42:08.0[A] -> GSI 54 (level, high) -> IRQ 225
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 57
GSI 23 sharing vector 0xE9 and IRQ 23
ACPI: PCI interrupt 0000:45:04.0[A] -> GSI 57 (level, high) -> IRQ 233
ACPI: PCI interrupt 0000:45:04.1[B] -> GSI 54 (level, high) -> IRQ 225
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ 4000000 size 65536 KB
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1217499817.182:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 40E182233A4BCA05
- User ID: CentOS (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU0] (supports C1)
ACPI: Processor [CPU1] (supports C1)
ACPI: Processor [CPU2] (supports C1)
ACPI: Processor [CPU3] (supports C1)
ACPI: Processor [CPU4] (supports C1)
ACPI: Processor [CPU5] (supports C1)
ACPI: Processor [CPU6] (supports C1)
ACPI: Processor [CPU7] (supports C1)
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP route cache hash table entries: 524288 (order: 10, 4194304 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 262144 (order: 10, 4194304 bytes)
TCP: Hash tables configured (established 262144 bind 262144)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 8 AMD Athlon 64 / Opteron processors (version 1.60.0)
powernow-k8: 0 : fid 0x16 (3000 MHz), vid 0x8 (1350 mV)
powernow-k8: 1 : fid 0x14 (2800 MHz), vid 0xa (1300 mV)
powernow-k8: 2 : fid 0x12 (2600 MHz), vid 0xc (1250 mV)
powernow-k8: 3 : fid 0x10 (2400 MHz), vid 0xe (1200 mV)
powernow-k8: 4 : fid 0xe (2200 MHz), vid 0x10 (1150 mV)
powernow-k8: 5 : fid 0xc (2000 MHz), vid 0x10 (1150 mV)
powernow-k8: 6 : fid 0xa (1800 MHz), vid 0x10 (1150 mV)
powernow-k8: 7 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
powernow-k8: cpu_init done, current fid 0x16, vid 0x8
powernow-k8: 0 : fid 0x16 (3000 MHz), vid 0xa (1300 mV)
powernow-k8: 1 : fid 0x14 (2800 MHz), vid 0xc (1250 mV)
powernow-k8: 2 : fid 0x12 (2600 MHz), vid 0xe (1200 mV)
powernow-k8: 3 : fid 0x10 (2400 MHz), vid 0x10 (1150 mV)
powernow-k8: 4 : fid 0xe (2200 MHz), vid 0x10 (1150 mV)
powernow-k8: 5 : fid 0xc (2000 MHz), vid 0x10 (1150 mV)
powernow-k8: 6 : fid 0xa (1800 MHz), vid 0x10 (1150 mV)
powernow-k8: 7 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
powernow-k8: cpu_init done, current fid 0x16, vid 0x8
powernow-k8: ph2 null fid transition 0x16
powernow-k8: 0 : fid 0x16 (3000 MHz), vid 0xa (1300 mV)
powernow-k8: 1 : fid 0x14 (2800 MHz), vid 0xc (1250 mV)
powernow-k8: 2 : fid 0x12 (2600 MHz), vid 0xe (1200 mV)
powernow-k8: 3 : fid 0x10 (2400 MHz), vid 0x10 (1150 mV)
powernow-k8: 4 : fid 0xe (2200 MHz), vid 0x10 (1150 mV)
powernow-k8: 5 : fid 0xc (2000 MHz), vid 0x10 (1150 mV)
powernow-k8: 6 : fid 0xa (1800 MHz), vid 0x10 (1150 mV)
powernow-k8: 7 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
powernow-k8: cpu_init done, current fid 0x16, vid 0xa
powernow-k8: 0 : fid 0x16 (3000 MHz), vid 0xa (1300 mV)
powernow-k8: 1 : fid 0x14 (2800 MHz), vid 0xc (1250 mV)
powernow-k8: 2 : fid 0x12 (2600 MHz), vid 0xe (1200 mV)
powernow-k8: 3 : fid 0x10 (2400 MHz), vid 0x10 (1150 mV)
powernow-k8: 4 : fid 0xe (2200 MHz), vid 0x10 (1150 mV)
powernow-k8: 5 : fid 0xc (2000 MHz), vid 0x10 (1150 mV)
powernow-k8: 6 : fid 0xa (1800 MHz), vid 0x10 (1150 mV)
powernow-k8: 7 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
powernow-k8: cpu_init done, current fid 0x16, vid 0xa
powernow-k8: 0 : fid 0x16 (3000 MHz), vid 0x8 (1350 mV)
powernow-k8: 1 : fid 0x14 (2800 MHz), vid 0xa (1300 mV)
powernow-k8: 2 : fid 0x12 (2600 MHz), vid 0xc (1250 mV)
powernow-k8: 3 : fid 0x10 (2400 MHz), vid 0xe (1200 mV)
powernow-k8: 4 : fid 0xe (2200 MHz), vid 0x10 (1150 mV)
powernow-k8: 5 : fid 0xc (2000 MHz), vid 0x10 (1150 mV)
powernow-k8: 6 : fid 0xa (1800 MHz), vid 0x10 (1150 mV)
powernow-k8: 7 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
powernow-k8: cpu_init done, current fid 0x16, vid 0x8
powernow-k8: 0 : fid 0x16 (3000 MHz), vid 0xa (1300 mV)
powernow-k8: 1 : fid 0x14 (2800 MHz), vid 0xc (1250 mV)
powernow-k8: 2 : fid 0x12 (2600 MHz), vid 0xe (1200 mV)
powernow-k8: 3 : fid 0x10 (2400 MHz), vid 0x10 (1150 mV)
powernow-k8: 4 : fid 0xe (2200 MHz), vid 0x10 (1150 mV)
powernow-k8: 5 : fid 0xc (2000 MHz), vid 0x10 (1150 mV)
powernow-k8: 6 : fid 0xa (1800 MHz), vid 0x10 (1150 mV)
powernow-k8: 7 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
powernow-k8: cpu_init done, current fid 0x16, vid 0xa
powernow-k8: 0 : fid 0x16 (3000 MHz), vid 0xa (1300 mV)
powernow-k8: 1 : fid 0x14 (2800 MHz), vid 0xc (1250 mV)
powernow-k8: 2 : fid 0x12 (2600 MHz), vid 0xe (1200 mV)
powernow-k8: 3 : fid 0x10 (2400 MHz), vid 0x10 (1150 mV)
powernow-k8: 4 : fid 0xe (2200 MHz), vid 0x10 (1150 mV)
powernow-k8: 5 : fid 0xc (2000 MHz), vid 0x10 (1150 mV)
powernow-k8: 6 : fid 0xa (1800 MHz), vid 0x10 (1150 mV)
powernow-k8: 7 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
powernow-k8: cpu_init done, current fid 0x16, vid 0xa
powernow-k8: 0 : fid 0x16 (3000 MHz), vid 0xa (1300 mV)
powernow-k8: 1 : fid 0x14 (2800 MHz), vid 0xc (1250 mV)
powernow-k8: 2 : fid 0x12 (2600 MHz), vid 0xe (1200 mV)
powernow-k8: 3 : fid 0x10 (2400 MHz), vid 0x10 (1150 mV)
powernow-k8: 4 : fid 0xe (2200 MHz), vid 0x10 (1150 mV)
powernow-k8: 5 : fid 0xc (2000 MHz), vid 0x10 (1150 mV)
powernow-k8: 6 : fid 0xa (1800 MHz), vid 0x10 (1150 mV)
powernow-k8: 7 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV)
powernow-k8: cpu_init done, current fid 0x16, vid 0xa
ACPI: (supports S0 S4 S5)
ACPI wakeup devices:

Freeing unused kernel memory: 196k freed
SCSI subsystem initialized
HP CISS Driver (v 2.6.10.RH1)
cciss: Device 0x3238 has been found at bus 66 dev 8 func 0
ACPI: PCI interrupt 0000:42:08.0[A] -> GSI 54 (level, high) -> IRQ 225
MSI INIT SUCCESS
cciss: using DAC cycles
blocks= 143305920 block_size= 512
heads= 255, sectors= 32, cylinders= 17562

Using cfq io scheduler
blocks= 143305920 block_size= 512
heads= 255, sectors= 32, cylinders= 17562

cciss/c0d0: p1 p2 p3 p4 < p5 p6 p7 >
QLogic Fibre Channel HBA Driver
ACPI: PCI interrupt 0000:08:00.0[A] -> GSI 18 (level, high) -> IRQ 193
qla2400 0000:08:00.0: Found an ISP2432, irq 193, iobase 0xffffff000001c000
qla2400 0000:08:00.0: Configuring PCI space...
PCI: Setting latency timer of device 0000:08:00.0 to 64
qla2400 0000:08:00.0: Configure NVRAM parameters...
qla2400 0000:08:00.0: Verifying loaded RISC code...
qla2400 0000:08:00.0: Allocated (64 KB) for EFT...
qla2400 0000:08:00.0: Allocated (1413 KB) for firmware dump...
qla2400 0000:08:00.0: Waiting for LIP to complete...
qla2400 0000:08:00.0: LIP reset occured (f700).
qla2400 0000:08:00.0: LIP occured (f700).
qla2400 0000:08:00.0: LIP reset occured (f7f7).
qla2400 0000:08:00.0: LOOP UP detected (4 Gbps).
qla2400 0000:08:00.0: Topology - (F_Port), Host Loop address 0x0
scsi0 : qla2xxx
qla2400 0000:08:00.0:
QLogic Fibre Channel HBA Driver: 8.01.07.25-fo
QLogic QMH2462 -
ISP2432: PCIe (2.5Gb/s x4) @ 0000:08:00.0 hdma+, host#=0, fw=4.00.90 [IP]
Vendor: HP Model: ESL E-Series Rev: 6.22
Type: Medium Changer ANSI SCSI revision: 03
Vendor: HP Model: Ultrium 3-SCSI Rev: L67W
Type: Sequential-Access ANSI SCSI revision: 03
Vendor: HP Model: Ultrium 3-SCSI Rev: L67W
Type: Sequential-Access ANSI SCSI revision: 03
Vendor: HP Model: Ultrium 3-SCSI Rev: L67W
Type: Sequential-Access ANSI SCSI revision: 03
Vendor: HP Model: Ultrium 3-SCSI Rev: L67W
Type: Sequential-Access ANSI SCSI revision: 03
Vendor: HP Model: Ultrium 3-SCSI Rev: L67W
Type: Sequential-Access ANSI SCSI revision: 03
Vendor: HP Model: Ultrium 3-SCSI Rev: L67W
Type: Sequential-Access ANSI SCSI revision: 03
Vendor: HP Model: Ultrium 3-SCSI Rev: L67W
Type: Sequential-Access ANSI SCSI revision: 03
Vendor: HP Model: Ultrium 3-SCSI Rev: L67W
Type: Sequential-Access ANSI SCSI revision: 03
Vendor: HP Model: Ultrium 3-SCSI Rev: L67W
Type: Sequential-Access ANSI SCSI revision: 03
Vendor: HP Model: Ultrium 3-SCSI Rev: L67W
Type: Sequential-Access ANSI SCSI revision: 03
Vendor: HP Model: Ultrium 3-SCSI Rev: L67W
Type: Sequential-Access ANSI SCSI revision: 03
Vendor: HP Model: Ultrium 3-SCSI Rev: L67W
Type: Sequential-Access ANSI SCSI revision: 03
Vendor: HP Model: OPEN-V Rev: 5009
Type: Direct-Access ANSI SCSI revision: 03
qla2400 0000:08:00.0: scsi(0:0:6:0): Enabled tagged queuing, queue depth 32.
SCSI device sda: 4195200 512-byte hdwr sectors (2148 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 4195200 512-byte hdwr sectors (2148 MB)
SCSI device sda: drive cache: write back
sda: sda1
Attached scsi disk sda at scsi0, channel 0, id 6, lun 0
Vendor: HP Model: OPEN-V Rev: 5009
Type: Direct-Access ANSI SCSI revision: 03
qla2400 0000:08:00.0: scsi(0:0:6:1): Enabled tagged queuing, queue depth 32.
SCSI device sdb: 1048577280 512-byte hdwr sectors (536872 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 1048577280 512-byte hdwr sectors (536872 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1
Attached scsi disk sdb at scsi0, channel 0, id 6, lun 1
Vendor: HP Model: OPEN-V Rev: 5009
Type: Direct-Access ANSI SCSI revision: 03
qla2400 0000:08:00.0: scsi(0:0:6:2): Enabled tagged queuing, queue depth 32.
SCSI device sdc: 1048577280 512-byte hdwr sectors (536872 MB)
SCSI device sdc: drive cache: write back
SCSI device sdc: 1048577280 512-byte hdwr sectors (536872 MB)
SCSI device sdc: drive cache: write back
sdc: sdc1
Attached scsi disk sdc at scsi0, channel 0, id 6, lun 2
Vendor: HP Model: OPEN-V Rev: 5009
Type: Direct-Access ANSI SCSI revision: 03
qla2400 0000:08:00.0: scsi(0:0:6:3): Enabled tagged queuing, queue depth 32.
SCSI device sdd: 1048577280 512-byte hdwr sectors (536872 MB)
SCSI device sdd: drive cache: write back
SCSI device sdd: 1048577280 512-byte hdwr sectors (536872 MB)
SCSI device sdd: drive cache: write back
sdd: sdd1
Attached scsi disk sdd at scsi0, channel 0, id 6, lun 3
Vendor: HP Model: OPEN-V Rev: 5009
Type: Direct-Access ANSI SCSI revision: 03
qla2400 0000:08:00.0: scsi(0:0:6:4): Enabled tagged queuing, queue depth 32.
SCSI device sde: 629145600 512-byte hdwr sectors (322123 MB)
SCSI device sde: drive cache: write back
SCSI device sde: 629145600 512-byte hdwr sectors (322123 MB)
SCSI device sde: drive cache: write back
sde: sde1
Attached scsi disk sde at scsi0, channel 0, id 6, lun 4
Vendor: HP Model: OPEN-V Rev: 5009
Type: Direct-Access ANSI SCSI revision: 03
qla2400 0000:08:00.0: scsi(0:0:6:5): Enabled tagged queuing, queue depth 32.
SCSI device sdf: 629145600 512-byte hdwr sectors (322123 MB)
SCSI device sdf: drive cache: write back
SCSI device sdf: 629145600 512-byte hdwr sectors (322123 MB)
SCSI device sdf: drive cache: write back
sdf: sdf1
Attached scsi disk sdf at scsi0, channel 0, id 6, lun 5
Vendor: HP Model: OPEN-V Rev: 5009
Type: Direct-Access ANSI SCSI revision: 03
qla2400 0000:08:00.0: scsi(0:0:6:6): Enabled tagged queuing, queue depth 32.
SCSI device sdg: 10487040 512-byte hdwr sectors (5369 MB)
SCSI device sdg: drive cache: write back
SCSI device sdg: 10487040 512-byte hdwr sectors (5369 MB)
SCSI device sdg: drive cache: write back
sdg: sdg1
Attached scsi disk sdg at scsi0, channel 0, id 6, lun 6
Vendor: HP Model: OPEN-V Rev: 5009
Type: Direct-Access ANSI SCSI revision: 03
qla2400 0000:08:00.0: scsi(0:0:6:7): Enabled tagged queuing, queue depth 32.
SCSI device sdh: 31457280 512-byte hdwr sectors (16106 MB)
SCSI device sdh: drive cache: write back
SCSI device sdh: 31457280 512-byte hdwr sectors (16106 MB)
SCSI device sdh: drive cache: write back
sdh: sdh1
Attached scsi disk sdh at scsi0, channel 0, id 6, lun 7
Vendor: HP Model: OPEN-V Rev: 5009
Type: Direct-Access ANSI SCSI revision: 03
qla2400 0000:08:00.0: scsi(0:0:6:8): Enabled tagged queuing, queue depth 32.
SCSI device sdi: 314572800 512-byte hdwr sectors (161061 MB)
SCSI device sdi: drive cache: write back
SCSI device sdi: 314572800 512-byte hdwr sectors (161061 MB)
SCSI device sdi: drive cache: write back
sdi: sdi1
Attached scsi disk sdi at scsi0, channel 0, id 6, lun 8
Vendor: HP Model: OPEN-V Rev: 5009
Type: Direct-Access ANSI SCSI revision: 03
qla2400 0000:08:00.0: scsi(0:0:6:9): Enabled tagged queuing, queue depth 32.
SCSI device sdj: 10487040 512-byte hdwr sectors (5369 MB)
SCSI device sdj: drive cache: write back
SCSI device sdj: 10487040 512-byte hdwr sectors (5369 MB)
SCSI device sdj: drive cache: write back
sdj: sdj1
Attached scsi disk sdj at scsi0, channel 0, id 6, lun 9
Vendor: HP Model: OPEN-V-CM Rev: 5009
Type: Direct-Access ANSI SCSI revision: 03
qla2400 0000:08:00.0: scsi(0:0:6:11): Enabled tagged queuing, queue depth 32.
SCSI device sdk: 96000 512-byte hdwr sectors (49 MB)
SCSI device sdk: drive cache: write back
SCSI device sdk: 96000 512-byte hdwr sectors (49 MB)
SCSI device sdk: drive cache: write back
sdk: unknown partition table
Attached scsi disk sdk at scsi0, channel 0, id 6, lun 11
Vendor: HP Model: OPEN-V*2 Rev: 5009
Type: Direct-Access ANSI SCSI revision: 03
qla2400 0000:08:00.0: scsi(0:0:6:12): Enabled tagged queuing, queue depth 32.
SCSI device sdl: 629145600 512-byte hdwr sectors (322123 MB)
SCSI device sdl: drive cache: write back
SCSI device sdl: 629145600 512-byte hdwr sectors (322123 MB)
SCSI device sdl: drive cache: write back
sdl: sdl1
Attached scsi disk sdl at scsi0, channel 0, id 6, lun 12
Vendor: HP Model: OPEN-V*2 Rev: 5009
Type: Direct-Access ANSI SCSI revision: 03
qla2400 0000:08:00.0: scsi(0:0:6:13): Enabled tagged queuing, queue depth 32.
SCSI device sdm: 1992295680 512-byte hdwr sectors (1020055 MB)
SCSI device sdm: drive cache: write back
SCSI device sdm: 1992295680 512-byte hdwr sectors (1020055 MB)
SCSI device sdm: drive cache: write back
sdm: sdm1
Attached scsi disk sdm at scsi0, channel 0, id 6, lun 13
ACPI: PCI interrupt 0000:08:00.1[B] -> GSI 19 (level, high) -> IRQ 217
qla2400 0000:08:00.1: Found an ISP2432, irq 217, iobase 0xffffff000001e000
qla2400 0000:08:00.1: Configuring PCI space...
PCI: Setting latency timer of device 0000:08:00.1 to 64
qla2400 0000:08:00.1: Configure NVRAM parameters...
qla2400 0000:08:00.1: Verifying loaded RISC code...
qla2400 0000:08:00.1: Allocated (64 KB) for EFT...
qla2400 0000:08:00.1: Allocated (1413 KB) for firmware dump...
qla2400 0000:08:00.1: Waiting for LIP to complete...
qla2400 0000:08:00.1: LIP reset occured (f700).
qla2400 0000:08:00.1: LIP occured (f700).
qla2400 0000:08:00.1: LIP reset occured (f7f7).
qla2400 0000:08:00.1: LOOP UP detected (4 Gbps).
qla2400 0000:08:00.1: Topology - (F_Port), Host Loop address 0x0
scsi1 : qla2xxx
qla2400 0000:08:00.1:
QLogic Fibre Channel HBA Driver: 8.01.07.25-fo
QLogic QMH2462 -
ISP2432: PCIe (2.5Gb/s x4) @ 0000:08:00.1 hdma+, host#=1, fw=4.00.90 [IP]
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 8
Attached scsi generic sg1 at scsi0, channel 0, id 0, lun 1, type 1
Attached scsi generic sg2 at scsi0, channel 0, id 0, lun 2, type 1
Attached scsi generic sg3 at scsi0, channel 0, id 1, lun 0, type 1
Attached scsi generic sg4 at scsi0, channel 0, id 1, lun 1, type 1
Attached scsi generic sg5 at scsi0, channel 0, id 2, lun 0, type 1
Attached scsi generic sg6 at scsi0, channel 0, id 2, lun 1, type 1
Attached scsi generic sg7 at scsi0, channel 0, id 3, lun 0, type 1
Attached scsi generic sg8 at scsi0, channel 0, id 3, lun 1, type 1
Attached scsi generic sg9 at scsi0, channel 0, id 4, lun 0, type 1
Attached scsi generic sg10 at scsi0, channel 0, id 4, lun 1, type 1
Attached scsi generic sg11 at scsi0, channel 0, id 5, lun 0, type 1
Attached scsi generic sg12 at scsi0, channel 0, id 5, lun 1, type 1
Attached scsi generic sg13 at scsi0, channel 0, id 6, lun 0, type 0
Attached scsi generic sg14 at scsi0, channel 0, id 6, lun 1, type 0
Attached scsi generic sg15 at scsi0, channel 0, id 6, lun 2, type 0
Attached scsi generic sg16 at scsi0, channel 0, id 6, lun 3, type 0
Attached scsi generic sg17 at scsi0, channel 0, id 6, lun 4, type 0
Attached scsi generic sg18 at scsi0, channel 0, id 6, lun 5, type 0
Attached scsi generic sg19 at scsi0, channel 0, id 6, lun 6, type 0
Attached scsi generic sg20 at scsi0, channel 0, id 6, lun 7, type 0
Attached scsi generic sg21 at scsi0, channel 0, id 6, lun 8, type 0
Attached scsi generic sg22 at scsi0, channel 0, id 6, lun 9, type 0
Attached scsi generic sg23 at scsi0, channel 0, id 6, lun 11, type 0
Attached scsi generic sg24 at scsi0, channel 0, id 6, lun 12, type 0
Attached scsi generic sg25 at scsi0, channel 0, id 6, lun 13, type 0
st: Version 20040403, fixed bufsize 32768, s/g segs 256
Attached scsi tape st0 at scsi0, channel 0, id 0, lun 1
st0: try direct i/o: yes (alignment 512 B), max page reachable by HBA 8912895
Attached scsi tape st1 at scsi0, channel 0, id 0, lun 2
st1: try direct i/o: yes (alignment 512 B), max page reachable by HBA 8912895
Attached scsi tape st2 at scsi0, channel 0, id 1, lun 0
st2: try direct i/o: yes (alignment 512 B), max page reachable by HBA 8912895
Attached scsi tape st3 at scsi0, channel 0, id 1, lun 1
st3: try direct i/o: yes (alignment 512 B), max page reachable by HBA 8912895
Attached scsi tape st4 at scsi0, channel 0, id 2, lun 0
st4: try direct i/o: yes (alignment 512 B), max page reachable by HBA 8912895
Attached scsi tape st5 at scsi0, channel 0, id 2, lun 1
st5: try direct i/o: yes (alignment 512 B), max page reachable by HBA 8912895
Attached scsi tape st6 at scsi0, channel 0, id 3, lun 0
st6: try direct i/o: yes (alignment 512 B), max page reachable by HBA 8912895
Attached scsi tape st7 at scsi0, channel 0, id 3, lun 1
st7: try direct i/o: yes (alignment 512 B), max page reachable by HBA 8912895
Attached scsi tape st8 at scsi0, channel 0, id 4, lun 0
st8: try direct i/o: yes (alignment 512 B), max page reachable by HBA 8912895
Attached scsi tape st9 at scsi0, channel 0, id 4, lun 1
st9: try direct i/o: yes (alignment 512 B), max page reachable by HBA 8912895
Attached scsi tape st10 at scsi0, channel 0, id 5, lun 0
st10: try direct i/o: yes (alignment 512 B), max page reachable by HBA 8912895
Attached scsi tape st11 at scsi0, channel 0, id 5, lun 1
st11: try direct i/o: yes (alignment 512 B), max page reachable by HBA 8912895
st7: Block limits 1 - 16777215 bytes.
st8: Block limits 1 - 16777215 bytes.
inserting floppy driver for 2.6.9-42.ELsmp
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
Ethernet Channel Bonding Driver: v2.6.3 (June 8, 2005)
bonding: MII link monitoring set to 100 ms
divert: allocating divert_blk for bond0
Ethernet Channel Bonding Driver: v2.6.3 (June 8, 2005)
bonding: MII link monitoring set to 100 ms
divert: allocating divert_blk for bond1
Ethernet Channel Bonding Driver: v2.6.3 (June 8, 2005)
bonding: MII link monitoring set to 100 ms
divert: allocating divert_blk for bond2
tg3.c:v3.52-rh (Mar 06, 2006)
ACPI: PCI interrupt 0000:07:04.0[A] -> GSI 19 (level, high) -> IRQ 217
divert: allocating divert_blk for eth0
eth0: Tigon3 [partno(011276-001) rev 9003 PHY(5714)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:1c:c4:46:1f:cd
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1]
eth0: dma_rwctrl[76148000]
ACPI: PCI interrupt 0000:07:04.1[B] -> GSI 16 (level, high) -> IRQ 201
divert: allocating divert_blk for eth1
eth1: Tigon3 [partno(011276-001) rev 9003 PHY(5714)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:1c:c4:46:1f:ce
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1]
eth1: dma_rwctrl[76148000]
ACPI: PCI interrupt 0000:45:04.0[A] -> GSI 57 (level, high) -> IRQ 233
divert: allocating divert_blk for eth2
eth2: Tigon3 [partno(N/A) rev 9003 PHY(5714)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:1e:0b:21:40:70
eth2: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1]
eth2: dma_rwctrl[76148000]
ACPI: PCI interrupt 0000:45:04.1[B] -> GSI 54 (level, high) -> IRQ 225
divert: allocating divert_blk for eth3
eth3: Tigon3 [partno(N/A) rev 9003 PHY(5714)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00:1e:0b:21:40:71
eth3: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1]
eth3: dma_rwctrl[76148000]
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.4.38 (February 10, 2006)
ACPI: PCI interrupt 0000:03:00.0[A] -> GSI 17 (level, high) -> IRQ 209
divert: allocating divert_blk for eth4
eth4: Broadcom NetXtreme II BCM5708 1000Base-SX (B2) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 209, node addr 001cc4a62782
ACPI: PCI interrupt 0000:05:00.0[A] -> GSI 16 (level, high) -> IRQ 201
divert: allocating divert_blk for eth5
eth5: Broadcom NetXtreme II BCM5708 1000Base-SX (B2) PCI-X 64-bit 133MHz found at mem fa000000, IRQ 201, node addr 001cc4a62786
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:01:04.4[B] -> GSI 17 (level, high) -> IRQ 209
uhci_hcd 0000:01:04.4: UHCI Host Controller
uhci_hcd 0000:01:04.4: irq 209, io base 0000000000001800
uhci_hcd 0000:01:04.4: new USB bus registered, assigned bus number 1
uhci_hcd 0000:01:04.4: port count misdetected? forcing to 2 ports
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 23 (level, high) -> IRQ 185
ehci_hcd 0000:00:02.1: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: irq 185, pci mem ffffff0000032000
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 22 (level, high) -> IRQ 177
ohci_hcd 0000:00:02.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 177, pci mem ffffff0000034000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 10 ports detected
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
usb 1-1: new full speed USB device using address 2
input: USB HID v1.01 Keyboard [HP Virtual Keyboard] on usb-0000:01:04.4-1
input: USB HID v1.01 Mouse [HP Virtual Keyboard] on usb-0000:01:04.4-1
usb 1-2: new full speed USB device using address 3
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 7 ports detected
ACPI: Power Button (FF) [PWRF]
EXT3 FS on cciss/c0d0p2, internal journal
device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on cciss/c0d0p1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on cciss/c0d0p6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on cciss/c0d0p3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2096440k swap on /dev/cciss/c0d0p5. Priority:-1 extents:1
Adding 32804688k swap on /dev/cciss/c0d0p7. Priority:-2 extents:1
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
bonding: bond0: enslaving eth0 as a backup interface with a down link.
tg3: eth0: Link is up at 1000 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.
bonding: bond0: link status definitely up for interface eth0.
bonding: bond0: making interface eth0 the new active one.
tg3: eth1: Link is up at 1000 Mbps, full duplex.
tg3: eth1: Flow control is off for TX and off for RX.
bonding: bond0: enslaving eth1 as a backup interface with an up link.
ip_tables: (C) 2000-2002 Netfilter core team
tg3: eth2: Link is up at 1000 Mbps, full duplex.
tg3: eth2: Flow control is off for TX and off for RX.
bonding: bond1: making interface eth2 the new active one.
bonding: bond1: enslaving eth2 as an active interface with an up link.
tg3: eth3: Link is up at 1000 Mbps, full duplex
tg3: eth3: Flow control is off for TX and off for RX.
bonding: bond1: enslaving eth3 as a backup interface with an up link.
ip_tables: (C) 2000-2002 Netfilter core team
bnx2: eth4: using MSI
bonding: bond2: enslaving eth4 as a backup interface with a down link.
bnx2: eth5: using MSI
bonding: bond2: enslaving eth5 as a backup interface with a down link.
bnx2: eth4 NIC Link is Up, 1000 Mbps full duplex
bonding: bond2: link status definitely up for interface eth4.
bonding: bond2: making interface eth4 the new active one.
bnx2: eth5 NIC Link is Up, 1000 Mbps full duplex
bonding: bond2: link status definitely up for interface eth5.
OCFS2 Node Manager 1.2.7 Tue Oct 9 16:16:05 PDT 2007 (build 1c4508be0c999c7bec8d997b52240db8)
OCFS2 DLM 1.2.7 Tue Oct 9 16:16:05 PDT 2007 (build 71e582227caabd47a4b94bc0f322b660)
OCFS2 DLMFS 1.2.7 Tue Oct 9 16:16:05 PDT 2007 (build 71e582227caabd47a4b94bc0f322b660)
OCFS2 User DLM kernel interface loaded
o2net: accepted connection from node srvpmld30-b (num 1) at 1.0.0.4:7777
OCFS2 1.2.7 Tue Oct 9 16:15:59 PDT 2007 (build d443ce77532cea8d1e167ab2de51b8c8)
ocfs2_dlm: Nodes in domain ("A1D7EBE18C9C4D618ECF6B03B452EFD5"): 0 1
kjournald starting. Commit interval 5 seconds
ocfs2: Mounting device (8,1) on (node 0, slot 0)
ocfs2_dlm: Nodes in domain ("2D5D2CC911E24FED9DC48E91D5ACFC4E"): 0 1
kjournald starting. Commit interval 5 seconds
ocfs2: Mounting device (8,17) on (node 0, slot 0)
ocfs2_dlm: Nodes in domain ("746BDFCDCC0E41158B47F259C7792A96"): 0 1
kjournald starting. Commit interval 5 seconds
ocfs2: Mounting device (8,33) on (node 0, slot 0)
ocfs2_dlm: Nodes in domain ("7D42422FF2B342A2BE07FEA5612F5E62"): 0 1
kjournald starting. Commit interval 5 seconds
ocfs2: Mounting device (8,49) on (node 0, slot 0)
ocfs2_dlm: Nodes in domain ("91E7B60C002445368E23D110F177730E"): 0 1
kjournald starting. Commit interval 5 seconds
ocfs2: Mounting device (8,65) on (node 0, slot 0)
ocfs2_dlm: Nodes in domain ("8E7E21658E81414F8B79E9D9C879D5CD"): 0 1
kjournald starting. Commit interval 5 seconds
ocfs2: Mounting device (8,81) on (node 0, slot 0)
ocfs2_dlm: Nodes in domain ("D8903384E2E2467DA9C30CFB588E59B3"): 0 1
kjournald starting. Commit interval 5 seconds
ocfs2: Mounting device (8,177) on (node 0, slot 0)
ocfs2_dlm: Nodes in domain ("CFE4DD69C4CA4802B39F7F258067CECD"): 0 1
kjournald starting. Commit interval 5 seconds
ocfs2: Mounting device (8,97) on (node 0, slot 0)
ocfs2_dlm: Nodes in domain ("DD5CD1B37FBA4B0C99965E31E4934ED0"): 0 1
kjournald starting. Commit interval 5 seconds
ocfs2: Mounting device (8,145) on (node 0, slot 0)
ocfs2_dlm: Nodes in domain ("5C198CEAC28841368D482F15A10A18A4"): 0 1
kjournald starting. Commit interval 5 seconds
ocfs2: Mounting device (8,129) on (node 0, slot 0)
ocfs2_dlm: Nodes in domain ("043FA84A9AF24290886AF8A46514C830"): 0 1
kjournald starting. Commit interval 5 seconds
ocfs2: Mounting device (8,193) on (node 0, slot 0)
ocfs2_dlm: Nodes in domain ("A3957C64A2B349D4AA9EADA870D2DD8C"): 0 1
kjournald starting. Commit interval 5 seconds
ocfs2: Mounting device (8,113) on (node 0, slot 0)
lp: driver loaded but no devices found
NET: Registered protocol family 10
Disabled Privacy Extensions on device ffffffff80405540(lo)
IPv6 over IPv4 tunneling driver
divert: not allocating divert_blk for non-ethernet device sit0
[snip ocfs stuff]

[Moreno Daltin]

Replying to myself, adding more details: when I use hp_rescan I get the following in dmesg

st0: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

st1: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

st10: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

st11: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

st2: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

st3: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

st4: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

st5: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

st6: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

st7: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

st8: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

st9: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

qla2400 0000:08:00.0: Scheduling rescan for new luns...

qla2400 0000:08:00.1: Scheduling rescan for new luns...

st0: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

st1: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

st10: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

st11: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

st2: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

st3: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

st4: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

st5: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

st6: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

st7: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

st8: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

st9: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).


and the following in /var/log/messages


Jul 31 10:02:35 srvpmld31-a kernel: st0: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

Jul 31 10:02:35 srvpmld31-a kernel: st1: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

Jul 31 10:02:35 srvpmld31-a kernel: st10: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

Jul 31 10:02:35 srvpmld31-a kernel: st11: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

Jul 31 10:02:35 srvpmld31-a kernel: st2: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

Jul 31 10:02:35 srvpmld31-a kernel: st3: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

Jul 31 10:02:35 srvpmld31-a kernel: st4: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

Jul 31 10:02:35 srvpmld31-a kernel: st5: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

Jul 31 10:02:35 srvpmld31-a kernel: st6: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

Jul 31 10:02:35 srvpmld31-a kernel: st7: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

Jul 31 10:02:35 srvpmld31-a kernel: st8: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

Jul 31 10:02:35 srvpmld31-a kernel: st9: Error 10000 (sugg. bt 0x0, driver bt 0x0, host bt 0x1).

Jul 31 10:02:53 srvpmld31-a sshd(pam_unix)[20442]: session opened for user root by root(uid=0)

Jul 31 10:02:58 srvpmld31-a kernel: qla2400 0000:08:00.0: Scheduling rescan for new luns...

Jul 31 10:02:58 srvpmld31-a kernel: qla2400 0000:08:00.1: Scheduling rescan for new luns...

Jul 31 10:03:21 srvpmld31-a kernel: st0: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

Jul 31 10:03:21 srvpmld31-a kernel: st1: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

Jul 31 10:03:21 srvpmld31-a kernel: st10: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

Jul 31 10:03:21 srvpmld31-a kernel: st11: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

Jul 31 10:03:21 srvpmld31-a kernel: st2: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

Jul 31 10:03:21 srvpmld31-a kernel: st3: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

Jul 31 10:03:21 srvpmld31-a kernel: st4: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

Jul 31 10:03:21 srvpmld31-a kernel: st5: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

Jul 31 10:03:21 srvpmld31-a kernel: st6: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

Jul 31 10:03:21 srvpmld31-a kernel: st7: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

Jul 31 10:03:21 srvpmld31-a kernel: st8: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

Jul 31 10:03:21 srvpmld31-a kernel: st9: Error 70000 (sugg. bt 0x0, driver bt 0x0, host bt 0x7).

[Marian Suchoicki_1]

Hello,

Has anyone posted a fix for this, or have you found a fix? I have the same issue.

Thanks Much

MS

[Trever Furnish]

I wish I could offer you some help, but all I can do here is comment that I'm experiencing a very similar problem on an Integrity (rx2660) running RHEL4.6. In my case it's only happening during backups to a VLS9000, and if I reboot the VLS9000, then do an 'hp_rescan -a', then I can communicate with the tape drives again. However I end up having to export and reformat the virtual tapes that were in use when the error occurred before I can use them again.

For me there are 8 VLS virtual tape drives presented and two fiberchannel HBAs in use for talking to them on two separate fabrics.