BladeSystem - General
cancel
Showing results for 
Search instead for 
Did you mean: 

Systems Insight Manager not identify blade

Neil Thirsk
Occasional Advisor

Systems Insight Manager not identify blade

I have a C3000 enclosure and am trying to get SIM to recognize it. I have tried doing a manual discovery and identify and it just reports back as unknown for system type.

I have reset the OA with no luck.

Any thoughts ???
11 REPLIES
Mi6t0
Trusted Contributor

Re: Systems Insight Manager not identify blade

What version of sim? And what version does the OA and the ilos have? Please make all of them uptodate and try again.
Neil Thirsk
Occasional Advisor

Re: Systems Insight Manager not identify blade

All ILO2s are running 1.35 and OA is running 2.03.

SIM is version C.05.01.00.02

Thanks
James ~ Happy Dude
Honored Contributor

Re: Systems Insight Manager not identify blade

Hello Neil,

You need to check you SNMP settings.
For Communication issues.. you may run Configure or Repair Agents.

Regards.
James ~ Happy Dude
Honored Contributor

Re: Systems Insight Manager not identify blade

Basically, You need to Configure SNMP service on the Client to accept packets from the SIM server. Then run Identify(under Options) task. Also, check if the WEBM is enabled(protocol settings page).

Regards.
James ~ Happy Dude
Honored Contributor

Re: Systems Insight Manager not identify blade

Ah ! I just came across this:

SNMP Config - Security Config - Add "CMS Server Name" READ_CREATE & Accept SNMP packets from these hosts = localhost, "CMS Server"
Trap Config - add " CMS Server Name" trap destination = CMS Name or IP Address
Restart the agents and some have to be removed from CMS and Re-Discovered.

;) Good Luck !

Regards.
James ~ Happy Dude
Honored Contributor

Re: Systems Insight Manager not identify blade

Please ignore the above post... that wasnt to be posted here.

;)
Neil Thirsk
Occasional Advisor

Re: Systems Insight Manager not identify blade

I have verified the SNMP settings and it is set to allow access from SIM. Below is the output from the Indentify process

Starting identification process...
Checking for known running web servers.
Checking for System Management Home Page and other HP web agents.
The System Management Homepage is not supported on this system.
Checking for WBEM support on system.
This system does not have any SMI-S CIMOM installed
This system doesn´t have a server CIMOM installed, or cannot connect to it using all credentials specified
Running WBEM rules based identification.
Cannot get ComputerSystem WBEM/WMI data from the system
Running WS-Man identification.
Checking for SNMP support on system.
The system responded to a SNMP request, it supports SNMP.
Running SNMP base Cluster identification using common cluster MIB.
This was not a system with the common cluster MIBs supported.
Running HP ProLiant management agent identification
System has the SNMP ProLiant desktop agents installed, adding system type.
Running HP NetServer identification.
System supports the NetServer SNMP agent, adding system type
Running HP-UX SNMP identification.
System does not have the HPUX SNMP agents installed.
Running SNMP System Type Manager identification.
No matching SNMP System Type Manager rule was found.
Checking for DMI protocol support.
The Windows CMS cannot communicate with HP-UX or other DMI, skipping.
Running DMI System Type Manager identification.
The system does not have Windows DMI support.
Running HP-UX DMI identification.
The system does not have HP-UX DMI support.
Running HP/Compaq Desktop identification.
The system does not have Windows DMI support.
Running HP DMI Desktop identification.
The system does not have HP DMI Desktop support.
Running Generic DMI identification.
The system does not have Generic DMI support.
Checking for SSH protocol support.
The system supports SSH protocol
Running Storage identification.
Did not detect WBEM support on this system. Will not attempt storage identification. If this is a storage host, check WBEM credentials and make sure the providers and CIMOM are operational on the host.
Storage identification completed.
Running HP Service Guard Identification.
The system is not part of HP Service Guard cluster
idPluginStart.IPMCompatible
Running VM identification.
Checking for license data on system.
SMH trust status is false.
Running limited data collection for common attribute.
Done with limited data collection, checking retrieved data.
Building system relationships.
System identification done with this system.
Mi6t0
Trusted Contributor

Re: Systems Insight Manager not identify blade

Ok, it could be SNMP, but I think it is better to upgrade the OA firmware to 2.04 and the ilo-s to the latest (i think it is 1.42). Then check if issue stays.
Raghuarch
Honored Contributor

Re: Systems Insight Manager not identify blade

Hi Neil,

Enable XML reply in OA.
it is present under Network setting
s Page.

Reagrds,
Raghuarch
Neil Thirsk
Occasional Advisor

Re: Systems Insight Manager not identify blade

That solved the issue.

Thank you .
Neil Thirsk
Occasional Advisor

Re: Systems Insight Manager not identify blade

Enabling XML response in the OA network settings resolved this issue.