- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: Unable to power blade 460c g7 back on after be...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-12-2012 06:15 AM
01-12-2012 06:15 AM
Unable to power blade 460c g7 back on after being powered off through ilo
I don't know if there is a wide issue out there, But we just got a c7000 blade chassis with bl 460c g7's and we replaced motherboards on atleast 9 of them. The issue was that when we powered them off through ilo, they could not be powered back on unless we did it physically by pressing the power button on the blade. Anyone experience this ? Each time i logged the call with hp they have replaced my mother board. Wonder if the next formware update would fix this ??
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-12-2012 10:12 AM - edited 01-18-2012 08:14 PM
01-12-2012 10:12 AM - edited 01-18-2012 08:14 PM
Re: Unable to power blade 460c g7 back on after being powered off through ilo
Hi,
This issue is due to ILO3 firmware version 1.25.
On an HP ProLiant G7-series server blade with HP Integrated Lights-out 3 (iLO 3) Firmware Version 1.25, the server blade may not "Auto Power On" and a manual power-on may be required.
This occurs because the "Auto Power On" setting is reversed. For example, if the "Auto Power On" feature is "Disabled", the server WILL perform an "Auto Power On."
RESOLUTION:
Version 1.26 of HP Integrated Lights-Out (iLO 3) will enable the server blade to perform an Auto Power On.
As a workaround, to ensure the server blade performs an Auto Power On, set the "Auto Power On" to "Disabled" on the "Power Management" >> "Server Power" page of the Integrated Lights-Out 3.
Select "Disabled instead of "On" because the "Auto Power On" setting is reversed.
Please refer the below advisory:
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c02913412
Before performing the firmware upgrade, please refer the below documents as well.
Refer the "HP BladeSystem Firmware Maintenance - Compatibility Matrix"
http://h18004.www1.hp.com/products/blades/components/c-class.html#tab3_content
Also, refer the HP BladeSystem ProLiant Firmware Management Best Practices - Implementer guide:
http://h20000.www2.hp.com/bc/docs/support/SupportManual/c02049593/c02049593.pdf
And, HP BladeSystem ProLiant Firmware Management - Technical white paper:
http://h20000.www2.hp.com/bc/docs/support/SupportManual/c02225412/c02225412.pdf
I hope the information will help you.
Regards,
Renji V
Was this post useful? -
To say thanks click the "thumbs up" icon below!!! .....
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-13-2012 10:20 AM - edited 01-13-2012 10:22 AM
01-13-2012 10:20 AM - edited 01-13-2012 10:22 AM
Re: Unable to power blade 460c g7 back on after being powered off through ilo
So you're saying this is due to ilo firmware version 1.26 ? But the adisory says that this is seen on systems with version 1.25. Either way all of our blades are allready on the latest and greatest ilo version firmware 1.26