Skip to ContentSkip to Footer
Start of content
- Community Home
- >
- Servers and Operating Systems
- >
- BladeSystem
- >
- BladeSystem - General
- >
- Using service port on C7000 to ilo on to Blades???...
BladeSystem - General
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
-
- Forums
-
Blogs
- Alliances
- Around the Storage Block
- Behind the scenes @ Labs
- HPE Careers
- HPE Storage Tech Insiders
- Infrastructure Insights
- Inspiring Progress
- Internet of Things (IoT)
- My Learning Certification
- OEM Solutions
- Servers: The Right Compute
- Shifting to Software-Defined
- Telecom IQ
- Transforming IT
- Infrastructure Solutions German
- L’Avenir de l’IT
- IT e Trasformazione Digitale
- Enterprise Topics
- ИТ для нового стиля бизнеса
- Blogs
-
Quick Links
- Community
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Contact
- Email us
- Tell us what you think
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Enterprise.nxt
- Marketplace
- Aruba Airheads Community
-
Forums
-
Blogs
-
InformationEnglish
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
04-16-2010 07:45 AM
04-16-2010 07:45 AM
Using service port on C7000 to ilo on to Blades????
I've managed to connect to the OA using the service port using the IP address on the Insight display. When I try to ILO on to a blade it fails, which I assume is because my IP range isn't the same as Blades IP. When I did a course on these, the instructor tried to show us a way using route add in dos. Has anyone managed to get this working?
2 REPLIES
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
04-16-2010 06:12 PM
04-16-2010 06:12 PM
Re: Using service port on C7000 to ilo on to Blades????
Koopa,
I didnt see that yet..The OA and ILO IP need to be from same VLAN.
I didnt see that yet..The OA and ILO IP need to be from same VLAN.
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
04-18-2010 11:09 PM
04-18-2010 11:09 PM
Re: Using service port on C7000 to ilo on to Blades????
Which addresses are on the same IP range?
The only reason I can think of for your PC not being able to connect to ILO on your server is if the GW information is wrong/missing.
Check in:
Enclosure Settings
- Enclosure Bay IP Adressing
Verify that the 'Shared Device Settings' are correct. (Subnet mask, gateway)
Also verify that each server's ILO port is enabled.
The only reason I can think of for your PC not being able to connect to ILO on your server is if the GW information is wrong/missing.
Check in:
Enclosure Settings
- Enclosure Bay IP Adressing
Verify that the 'Shared Device Settings' are correct. (Subnet mask, gateway)
Also verify that each server's ILO port is enabled.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
End of content
United States
Hewlett Packard Enterprise International
Communities
- Communities
- HPE Blogs and Forum
© Copyright 2019 Hewlett Packard Enterprise Development LP