- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: VC FC issues... Cannot see the Presented Lun ...
BladeSystem - General
1753797
Members
7831
Online
108799
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-30-2008 07:16 PM
06-30-2008 07:16 PM
VC FC issues... Cannot see the Presented Lun till VC Modules are Rebooted
Has anyone had the issue when placing a new blade in one cannot see the presented LUNS until the process of shutting down all the blades in the enclosure and then shutting down the VC FC Modules.
I have updated to 1.21 for the VC FC and 2.21??for the OA. After which I have not seen the issue however I have not added any more blades in. So part of the issue has been resolved but the part of adding a new blade and getting it presented has not since been tested.
I guess my question is, am I alone in this issue or have other people had this issue and what did you do to resolve it?
I have updated to 1.21 for the VC FC and 2.21??for the OA. After which I have not seen the issue however I have not added any more blades in. So part of the issue has been resolved but the part of adding a new blade and getting it presented has not since been tested.
I guess my question is, am I alone in this issue or have other people had this issue and what did you do to resolve it?
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-22-2008 02:51 AM
07-22-2008 02:51 AM
Re: VC FC issues... Cannot see the Presented Lun till VC Modules are Rebooted
You might want to try latest VC firmware. And check from Your HBA BIOS that the "point-to-point only" setting is enabled.
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c00874480〈=en&cc=us&taskId=101&prodSeriesId=3201246&prodTypeId=329290
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c00874480〈=en&cc=us&taskId=101&prodSeriesId=3201246&prodTypeId=329290
Remember to give Kudos to answers! (click the KUDOS star)
You can find me from Twitter @JKytsi
You can find me from Twitter @JKytsi
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP