HPE Community read-only access December 15, 2018
This is a maintenance upgrade. You will be able to read articles and posts, but not post or reply.
Hours:
Dec 15, 4:00 am to 10:00 am UTC
Dec 14, 10:00 pm CST to Dec 15, 4:00 am CST
Dec 14, 8:00 pm PST to Dec 15, 2:00 am PST
BladeSystem - General
cancel
Showing results for 
Search instead for 
Did you mean: 

c7000 and uplink throughput

 
SOLVED
Go to solution
UK-Blr
Frequent Advisor

c7000 and uplink throughput

Hi,

I am just wondering and to understand more:

In a C7000 encosure with 6 VC Ethernet modules loaded (3 active, 3 standby and Four 1GB uplink port on each Ethernet module) and, if we uplink all the ports on the active bays 1,3,5,7 to a single uplink ether channel and standby bay module ports on 2,4,6,8 to another single uplink ether channel connected to a different switch, using trunk option in a cisco switching environment.

Do i get 16GB trunk throughput of active and 16GB throughput of standby. Any issues with this coniguration?
6 REPLIES
Adrian Clint
Honored Contributor
Solution

Re: c7000 and uplink throughput

Uday, You can only have etherchannel trunks from a single VC module. You cannot span a trunk accross different VCs. So with 8 VC modules you would have eight 4GB trunks.

What you could do is buy 10GB CX4 0.5m stacking cables and connect up all the VC modules then you could have four 8GB trunks.

As for active/passive - that depends on your VC network design. You could have them all active.
UK-Blr
Frequent Advisor

Re: c7000 and uplink throughput

Thanks for clarifying. Yes we have cx4 cable for vc module communication/redundancy.
UK-Blr
Frequent Advisor

Re: c7000 and uplink throughput

with this in mind, it created one more new question.

Assume if we have two different active 4gb Access port uplinks from different vc ethernet module.
Later if we add the whole active 8 gb uplink nics(4gb + 4gb)connected to a single vmware virtual switch, how does it behave.
Adrian Clint
Honored Contributor

Re: c7000 and uplink throughput

By default the VC uplinks are usually set to Auto. Which is to auto form fully active trunks if the trunks are configured by the switch.

So as long as you configure all 8 ports in an etherchannel trunk at the switch end (single or stacked switchs) on the VC end they will auto configure to an 8GB trunk.
UK-Blr
Frequent Advisor

Re: c7000 and uplink throughput

ok...

heregoes more details.

One ether channel access port for 4 uplinks in VC module-1

One more ether channel access port of 4 uplinks in VC module-3

So i have total 8Gb uplink, if we combine alotgether in vmware virtual switch.

I am sure this creates routing issues, because of two different ether access channels, combined using vmware vswitch.

But, just searching is this option works really or not.

Adrian Clint
Honored Contributor

Re: c7000 and uplink throughput

That just gives you two 4GB uplinks (as they are through different VCs).
So thats "Scenario 10: Network failover with LACP" in the Virtual Connect Ethernet Cookbook. "The uplinks connected to VC-Enet module 1 and 3 cannot be combined for aggregated bandwidth". So its 4GB Active/4GB Passive.

Take a look at Scenario 11, 12A or 12B in the cookbook to get 8GB usable bandwidth.