HPE Community read-only access December 15, 2018
This is a maintenance upgrade. You will be able to read articles and posts, but not post or reply.
Hours:
Dec 15, 4:00 am to 10:00 am UTC
Dec 14, 10:00 pm CST to Dec 15, 4:00 am CST
Dec 14, 8:00 pm PST to Dec 15, 2:00 am PST
BladeSystem - General
cancel
Showing results for 
Search instead for 
Did you mean: 

can't show the blade servers on RDP console section..

 
markum fuadi
Frequent Advisor

can't show the blade servers on RDP console section..

Dear All,


recently we faced this scenario;
we had :
- 1 (one) c-7000 enclosure, with 1 (one) OA and with 2(two) pass through installed..

- 3 (three) bl-460c g1 installed. at bay 1,2 and 3.

- 1 (one) dl-145 as a RDP server.


need help guys, can u show me the right procedure, whitepappers or manual guide.. howto show the blade server using an on RDP console server???


the communication between OA, the blades and the rdp server itself are good.. i already set the ip addresses on each of the servers..and it is sucessfull when ping between them..

fyi,at HP SIM on rdp server.. the blades are sucessfully autodiscover..

i allready installed the ICDVD220 with the rdp on it.. but when i try open the RDP console,.. i can't find/ discover the blade's server at the computers section???

do i must setup it manually or it can be like autodiscover guys???

is it something do i miss out???

need help guys...!!!
tks a lot..

www.markumfuadi.co.cc
7 REPLIES
JKytsi
Honored Contributor

Re: can't show the blade servers on RDP console section..

Hi,
You must enable physical view and pxe boot your blades.
Remember to give Kudos to answers! (click the KUDOS star)

You can find me from Twitter @JKytsi
Raghuarch
Honored Contributor

Re: can't show the blade servers on RDP console section..

Do refer to the below link for Setup, install, and configure RDP.
There are Manuals and Troubleshoot a problem section also.

http://h20000.www2.hp.com/bizsupport/TechSupport/Home.jsp?lang=en&cc=us&prodTypeId=18964&prodSeriesId=332359
Cederberg
Honored Contributor

Re: can't show the blade servers on RDP console section..

Hey!

As said above the RDP needs to Discover the server before it can show in the RDP console. The RDP need the RDP agent on the server with the right settings.

If you don't have OS you PXE boot the server the it will be discovered and you can see it in physical view and as an object.

If you have OS without an agent then you need to use the Agent remote installer to install the agent from the RDP.

If you have OS with agent then you need to verify connections and settings in the agent.
markum fuadi
Frequent Advisor

Re: can't show the blade servers on RDP console section..

tks guys,

it's dhcp and pxe server issue..
i set them both.. and.. it works now..
i can see my new blades already..

at O/S to build section on RDP installation.. i choose.. win2003 & win2000 Advanced server..

i already success with the simulation of "deploy, read & write" jobs assign on my blades.. with that 2 O/S above..

my question is ;
1."is it possible to add another O/S to integrated on my existing rdp server??.. i want to add RHEL O/S.. for example.."

if possible.. show me the guide guys..!!!
please..!!!

2."how to erase the system/array configuration on my blade using rdp ???

coz having failed result when...
i assign jobs from the jobs panel "Server Deployment Toolbox--->Hardware configuration--->Array--->Erase Proliant ML/DL/BL Array configuration (winPE)".. and
"Server Deployment Toolbox--->System--->Erase Proliant ML/DL/BL System Configuration (winPE).

any other idea guys , beside clear-ing the configuration by RBSU.. ????


need help guys,

tks
cheers,

markum@asa.co.id









www.markumfuadi.co.cc
Steven Clementi
Honored Contributor

Re: can't show the blade servers on RDP console section..

"1."is it possible to add another O/S to integrated on my existing rdp server??.. i want to add RHEL O/S.. for example..""

If you re-run the RDP installation, there is a step that runs after the main Altiris install. This is the step that puts in all the HP specific and OS specific settings. Running this will allow you to add any of the supported Operating Systems to your installation.


What you are looking to run is the "Proliant Integration Module". I attached a ascreenshot.
Steven Clementi
HP Master ASE, Storage and Clustering
MCSE (NT 4.0, W2K, W2K3)
VCP (ESX2, Vi3, vSphere4, vSphere5)
RHCE
NPP3 (Nutanix Platform Professional)
markum fuadi
Frequent Advisor

Re: can't show the blade servers on RDP console section..

tk's steve..

you make my day brighter now.. ^_^
btw steve.. regarding my second question.. bout erasing the blade.. any solution???

can u show me the right procedure??

i'm looking forward for any other solution..


cheers,
markum@asa.co.id
www.markumfuadi.co.cc
markum fuadi
Frequent Advisor

Re: can't show the blade servers on RDP console section..

guys,

is win2008 server already ready for deployment on my ICDVD220.. RDP v.3.70???


help guys,
tks
www.markumfuadi.co.cc