- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- ebipa ip address
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-18-2007 11:21 PM
тАО10-18-2007 11:21 PM
ebipa ip address
after ebipa first setup (C7000) i have tried to change initial enclosure bay ip addresses but without success.
Do i have to follow i specific procedure - i cannot find any.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-19-2007 02:29 AM
тАО10-19-2007 02:29 AM
Re: ebipa ip address
There is no specific procedure to change the EBIPA. You can type in the IP in EBIPA page and Enable EBIPA and Click on Apply.
Syslog should give a message that the EBIPA IP address is modified to the New IP.
If the IP is not applied you should get a error in Syslog. r u getting any error?
Regards,
Raghuarch
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-21-2007 07:57 AM
тАО10-21-2007 07:57 AM
Re: ebipa ip address
They must be set to DHCP for EBIPA to work.
If they are not, set them all to DHCP then reconfigure EBIPA and watch the IP addresses change when they are reset.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-21-2007 11:44 PM
тАО10-21-2007 11:44 PM
Re: ebipa ip address
Refer:
h20000.www2.hp.com/bc/docs/support/SupportManual/c00705292/c00705292.pdf
Page 77 onwards,
James.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-22-2007 05:01 AM
тАО10-22-2007 05:01 AM
Re: ebipa ip address
Thanxs
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-29-2007 01:52 AM
тАО10-29-2007 01:52 AM