- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- gbe2c x-connect configuration
BladeSystem - General
1753309
Members
6747
Online
108792
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-20-2009 01:09 AM
08-20-2009 01:09 AM
gbe2c x-connect configuration
hi,
Just wanted to confirm the correct configuration for x-connecting 2 gbe2c switches in a C7000 enclosure.
Bay1 & 2 - gbe2c for internal network. Default VLAN settings (i.e. all ports on same vlan). I need to:
1) enable port 17 & 18 on both switches
2) enable STP. I am assuming RSTP would be what I need to use. Never configured STP before, is there anything specifically I need to do?
I also have 2 switches in bay 5 & 6, and would then do the same configuration as per above for these 2. Bay 5 & 6 are used for external connectivity to other networks.
Just wanted to confirm the correct configuration for x-connecting 2 gbe2c switches in a C7000 enclosure.
Bay1 & 2 - gbe2c for internal network. Default VLAN settings (i.e. all ports on same vlan). I need to:
1) enable port 17 & 18 on both switches
2) enable STP. I am assuming RSTP would be what I need to use. Never configured STP before, is there anything specifically I need to do?
I also have 2 switches in bay 5 & 6, and would then do the same configuration as per above for these 2. Bay 5 & 6 are used for external connectivity to other networks.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-20-2009 04:35 AM
08-20-2009 04:35 AM
Re: gbe2c x-connect configuration
There is a specific forum for the switches from the manufacturer. You may find the commands already in a question response.
http://www.bladeconnect.com/
http://www.bladeconnect.com/
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP