HPE Community read-only access December 15, 2018
This is a maintenance upgrade. You will be able to read articles and posts, but not post or reply.
Hours:
Dec 15, 4:00 am to 10:00 am UTC
Dec 14, 10:00 pm CST to Dec 15, 4:00 am CST
Dec 14, 8:00 pm PST to Dec 15, 2:00 am PST
BladeSystem - General
cancel
Showing results for 
Search instead for 
Did you mean: 

how to access blade c7000 OA using GUI

 
SOLVED
Go to solution
Basheer_2
Trusted Contributor

how to access blade c7000 OA using GUI

Hello all,

c7000 blade.
able to ssh to OA.

how do I get gui access to OA.
tried http://IP-of-OA no luck.

Thanks for your help.
13 REPLIES
Cederberg
Honored Contributor

Re: how to access blade c7000 OA using GUI

Hi.

sounds like either a hanged OA or the option for https has been disabled.

When you ssh to the c7000 chassi typ in "enable https" without the quotation marks. That enables the web access to the OA if it has been disabled.
Jimmy Vance
HPE Pro

Re: how to access blade c7000 OA using GUI

A little more info about your setup might help resolve quicker. Can you ping or ssh to the OA? Are you sure the OA is connected to a network?



__________________________________________________
No support by private messages. Please ask the forum!      I work for HPE

If you feel this was helpful please click the KUDOS! thumb below!   
Basheer_2
Trusted Contributor

Re: how to access blade c7000 OA using GUI

Hello Cederberg,

enable https
says

already enabled.

is there any port # I need to put after the http://OA-IP
https://OA-IP

Adrian Clint
Honored Contributor

Re: how to access blade c7000 OA using GUI

No port numbers needed.

Have you verified its not the network, firewall or a browser proxy setting?
Frank Gessner
Frequent Advisor

Re: how to access blade c7000 OA using GUI

disable proxy on your browser.
The Brit
Honored Contributor
Solution

Re: how to access blade c7000 OA using GUI

Hi Basheer.

Be sure you are using the appropriate IP address,

Basic question:: Can you ping this IP Address (I assume YES)??

When you log in to the OA (via SSH) does it say that the "OA Role: Active"

If not, do a "show network" and check at the bottom that "Enclosure IP Mode: Enabled", it could be that you are attempting to connect to the Standby OA.

Dave
marcus1234
Honored Contributor

Re: how to access blade c7000 OA using GUI

connect laptop directly to OA is access all okay via web now,
with browser explorer max version 7 for good measure.

what happens now..
Johan Guldmyr
Honored Contributor

Re: how to access blade c7000 OA using GUI

Heya, have you looked in the front of the enclosure in the insight display? Is there an IP set?
Johan Guldmyr
Honored Contributor

Re: how to access blade c7000 OA using GUI

Also, while you're in there, make sure that the OA Ethernet port have link :)
Braveheart360
Occasional Visitor

Re: how to access blade c7000 OA using GUI

Hello all,

Has anyone identified an answer to Basheer's GUI connection failure? The C7000 OA is currently running v2.60 Firmware. The chassis domain I have been experiencing the same failure after updating the OA CA Certificate and rebooting the OAs, but have tested the following and completed the following.

Hardware Connectivity Tested:
+ Hardware Failures - None
+ Chassis Service Port IP - Validated
+ Chassis Service Port Telnet - Validated
+ Chassis Service Port GUI - Fails
+ OA IP - Validated
+ OA Telnet - Validated
+ OA GUI - Fails

Troubleshooting Completed to date:
+ Generate telnet OA "SHOW OA INFO" and "SHOW OA STATUS" - Information is correct
+ Remove redundant OA and reboot OA1 to validate connectivity - OA1 is only active OA
+ Telnet into OA1 and replace the Certificate with self-signed certificate - Information displayed by SHOW OA CERTIFICATE" is correct
Disabled and re-enabled HTTPS from telnet - Enable does work
The Brit
Honored Contributor

Re: how to access blade c7000 OA using GUI

Hey there Willy Wallace,

Basheer kinda stopped talking to us, implying that maybe one of the suggestions worked for him, however he didn't tell us what that was!!

maybe this will get a response from him.

Dave.
Braveheart360
Occasional Visitor

Re: how to access blade c7000 OA using GUI

Sorry to hear that there hasn't been an identified solution for Basheer.

Do you happen to know how the OA Web is served out? It appears as though there is a certificate error that may be causing the internal web host to appear invalid.

Would this potentially cause the failure?
The Brit
Honored Contributor

Re: how to access blade c7000 OA using GUI

I dont think the certificate error is a show-stopper. I get certificate errors everytime I connect to either OA or VCM. I just hit the "Continue to this website" link. It is a nuisance, but hey...

Dave.