- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: install W2K3 SP1 to bl860c with ONE disk
BladeSystem - General
1753809
Members
7724
Online
108805
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-18-2009 06:54 AM
тАО03-18-2009 06:54 AM
install W2K3 SP1 to bl860c with ONE disk
Hi guys!
I cannot install w2k3 to server if bl860c has one disk. Setup create partition but next message is "cannot gain access to the disk".
If put second hard drive and make RAID on two disks, all is right. Windows setup seen volume and start instalation.
Why it cannot setup with only one disk?
LSI controller cannot create raid0 in one disk, I attemped it.
I cannot install w2k3 to server if bl860c has one disk. Setup create partition but next message is "cannot gain access to the disk".
If put second hard drive and make RAID on two disks, all is right. Windows setup seen volume and start instalation.
Why it cannot setup with only one disk?
LSI controller cannot create raid0 in one disk, I attemped it.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-20-2009 02:15 AM
тАО03-20-2009 02:15 AM
Re: install W2K3 SP1 to bl860c with ONE disk
Hi,
this is because W2K3 does not have a driver build in to understand the LSI SAS controllers presentation of the SAS disk. If you create a raid1 then this emulates how a SCSI device presents himself and that W2K3 does understand.
W2K8 can install on a single disk since it thas the fix build in natively now.
HTH
Kris
this is because W2K3 does not have a driver build in to understand the LSI SAS controllers presentation of the SAS disk. If you create a raid1 then this emulates how a SCSI device presents himself and that W2K3 does understand.
W2K8 can install on a single disk since it thas the fix build in natively now.
HTH
Kris
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-01-2011 01:54 AM
тАО03-01-2011 01:54 AM
Re: install W2K3 SP1 to bl860c with ONE disk
thanks
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP