- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: nparstatus fail on rp7410
BladeSystem - General
1753788
Members
7464
Online
108799
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-04-2010 05:39 PM
02-04-2010 05:39 PM
nparstatus fail on rp7410
I have 1 rp7420 and 1 rp7410
I get ignite from rp7420 and restore on rp7410.
But, on boot I get the following error on /etc/rc.log
CRDHP03 >/sbin/rc2.d/S602icod start
ERROR: The following low-level error occurred:
@4:Software error.[Error on ioctl.]No such device or address
ERROR: The following low-level error occurred:
@4:Software error.[Error on ioctl.]No such device or address
ERROR: The Instant Capacity (iCAP) Agent
was unable to reconcile the number of active
processors with the intended number of active
processors. For further information about
the Instant Capacity status, run icapstatus (1m).
I have determined that the error is in the parstatus:
CRDHP03 >parstatus
Note: No action specified. Default behavior is display all.
CIM_ERR_FAILED: HPNPAR4:@4:Software error.[A time-out occurred waiting for a response from the IPMI request 6:1(NetFn:Cmd). status codes returned were -1:0:6(ioctl function return:cCode:errno).
]No such device or address
Note: Unable to get any HP_NParComplex information.
Error: Unsupported platform.
how can I correct it?
I get ignite from rp7420 and restore on rp7410.
But, on boot I get the following error on /etc/rc.log
CRDHP03 >/sbin/rc2.d/S602icod start
ERROR: The following low-level error occurred:
@4:Software error.[Error on ioctl.]No such device or address
ERROR: The following low-level error occurred:
@4:Software error.[Error on ioctl.]No such device or address
ERROR: The Instant Capacity (iCAP) Agent
was unable to reconcile the number of active
processors with the intended number of active
processors. For further information about
the Instant Capacity status, run icapstatus (1m).
I have determined that the error is in the parstatus:
CRDHP03 >parstatus
Note: No action specified. Default behavior is display all.
CIM_ERR_FAILED: HPNPAR4:@4:Software error.[A time-out occurred waiting for a response from the IPMI request 6:1(NetFn:Cmd). status codes returned were -1:0:6(ioctl function return:cCode:errno).
]No such device or address
Note: Unable to get any HP_NParComplex information.
Error: Unsupported platform.
how can I correct it?
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-08-2010 03:43 AM
02-08-2010 03:43 AM
Re: nparstatus fail on rp7410
Hello Fernando,
This sounds like a problem with WBEM. Check that the directory /var/opt/wbem/repository contains:
root#cimv2#npar or
root#cimv2#npar.db (11.31)
If WBEM works in general (check with command osinfo) you might need to (re-)install the NPar-Provider.
Frauke
This sounds like a problem with WBEM. Check that the directory /var/opt/wbem/repository contains:
root#cimv2#npar or
root#cimv2#npar.db (11.31)
If WBEM works in general (check with command osinfo) you might need to (re-)install the NPar-Provider.
Frauke
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP