- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Using service port to access the iLO's?
BladeSystem - General
1753797
Members
7988
Online
108805
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-21-2008 02:31 PM
тАО01-21-2008 02:31 PM
Using service port to access the iLO's?
Hello, Connected to the service port on the Management sleeve it is possible to access the OA using the Service IP address. Is it also possible to access the iLO's of the Blades using this service bus? (In case of a broken OA?). Are there any other reasons why to use this bus? Lodewijk
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-09-2008 02:11 PM
тАО08-09-2008 02:11 PM
Using service port to access the iLO's?
That port's for linking enclosures so you can manage up to 4 enclosures as one, not for OA management/iLO access. Hope this helps. Phil.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-26-2009 09:52 PM
тАО01-26-2009 09:52 PM
Using service port to access the iLO's?
In the last connected chassis, you can connect a laptop to connect to the service address of the OAs. With the current OAs, depending on the laptop model, 100M is the max connected speed. With my Lenovo T60, I have had limited success in connecting to this service port. You can use this to configure OA prior to connecting into your production network, rather than the LCD panel to enter static IP addresses. Neal
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-25-2009 03:47 PM
тАО04-25-2009 03:47 PM
Using service port to access the iLO's?
Would suggest you to connect to individual modules using the service port/uplink port and set a common password for all the OA modules in all the enclosures - Then connect your daisy chain to link all the enclosures in your rank and you can manage assign IPs before you connect the OA modules to your network. You can't use a service port to access iLo's Please try this if you are trying to access iLo's before connecting to your OA modules to the network. - Connect to Service port and assign EBIPA to your bays by giving subnet mask 255.255.0.0 and gateway IP as your laptop ( 169.254.0.x - where x is different from your service port IP) assign 169.254.0.A to 169.254.0.Z ( IPs A through Z should not be the service port IP) assing OA1 IP as 169.254.0.X ( Where X should not be the service port IP) Once you assing this - Connect your laptop directly to Active OA port and start accessing both the enclosure as well as blades - This saves us lot of time to do pre-configuration work Remember not to change the IPs back to your production before logging out from the OA Hope this is clear - Thanks
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP