- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: HP 1:10Gb Ethernet Blade Switch, not getting I...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-16-2018 05:31 PM - edited тАО10-17-2018 06:55 AM
тАО10-16-2018 05:31 PM - edited тАО10-17-2018 06:55 AM
HP 1:10Gb Ethernet Blade Switch, not getting IP via EBIPA service OA
HI Guys:
I am trying to configure the HP 1:10 Ethernet Blade Switch, to get ILO management IP via EBIPA from OA, for this I have enabled DHCP by command using console access, I enabled if 256 (management interface) and DHCP service on switch:
Current idle CLI timeout: 5 minutes
System will reset on crash
Use of BOOTP for configuration currently enabled
Use of DHCP for management interface configuration currently enabled <---- DHCP is enabled which is supposed to overwrite any IP configured for management interface (if 256) but that is not my case.
=> Pending configuration
/c/l3/if 256
ena
addr 0.0.0.0
mask 0.0.0.0
broad 255.255.255.255
Current status: disabled
New status: enabled
Error: Invalid address for IP interface 256.
Error: Invalid address / mask pair for IP interface 256.
Error: Apply not done. Use "diff" to see pending changes,
then use configuration menus to correct errors.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-18-2018 07:34 AM
тАО10-18-2018 07:34 AM
Re: HP 1:10Gb Ethernet Blade Switch, not getting IP via EBIPA service OA
Hi HP community, any assistance you can add on this?
If I add IP manually to the interface 256 (management) it is not opening the web console, also I cannot telnet that IP.
Hope someone can help on this.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-23-2018 08:16 AM
тАО10-23-2018 08:16 AM
Re: HP 1:10Gb Ethernet Blade Switch, not getting IP via EBIPA service OA
Refer installation guide .
https://support.hpe.com/hpsc/doc/public/display?sp4ts.oid=5039543&docLocale=en_US&docId=emr_na-c01055384
If this was working earlier and now stopped working ..would suggest to contact HPE support and open a support ticket to investigate and fix .
If this is a installation time error refer installation guide to configure .
https://support.hpe.com/hpsc/doc/public/display?sp4ts.oid=5039543&docLocale=en_US&docId=emr_na-c01055384
From the serial console interface, be sure that the switch IP address is configured and valid on the network.
I am a HPE employee
__________________________________________
Was the post useful? Click on the white KUDOS! Thumb below to say Thank You!