- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- BL460c G6 will not turn on and Led Health blink R...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-12-2017 09:42 AM
12-12-2017 09:42 AM
BL460c G6 will not turn on and Led Health blink Red.
Hello, i have a Enclosure C7000 with 10x BL460c G6, and now i installing more one BL460c G6, but this new server will not turn on (Video doesn't apppear in SVC Cable) and the led health blink red. In the status of Enclosure, the Blade is recognize, but even so doesn't recognize the iLO (MAC ADDRESS 00:00:00:00:00:00), and doesn't recognize the ROM version. I already tested on two enclosures (version OA 4.11 and 4.60), but the error remains.
Info New Blade:
Server Blade #7 Information: Type: Server Blade Manufacturer: HP Product Name: HP ProLiant BL460c G6 Part Number: [Unknown] System Board Spare Part Number: 595046-001 Serial Number: [Unknown] UUID: Server Name: [Unknown] Asset Tag: [Unknown] ROM Version: [Unknown] Flex-10 Embedded Ethernet Port 1: 1C:C1:DE:01:61:88 Port 2: 1C:C1:DE:01:61:8C Mezzanine 1: HP NC382m Dual Port 1GbE Multifunction BL-c Adapter Port 1: d8:d3:85:c0:62:f4 Port 2: d8:d3:85:c0:62:f6 Mezzanine 2: QLogic QMH2562 8Gb FC HBA for HP BladeSystem c-Class Port 1: 50:01:43:80:07:2b:0a:28 Port 2: 50:01:43:80:07:2b:0a:2a Management Processor Information: Type: [Unknown] Name: [Acquiring] Firmware Version: 2.00 IP Address: 0.0.0.0 MAC Address: 00:00:00:00:00:00 Power Management Controller Version: Not Available iLO Federation Capable: No
Status:
Blade #7 Status: Power: Off Current Wattage used: 0 Health: Other Unit Identification LED: Off Virtual Fan: 0% Diagnostic Status: Internal Data OK Management Processor OK I/O Configuration OK Device Failure OK Device Degraded OK iLO Network Other
- Info OA:
Onboard Administrator #1 information: Product Name : BladeSystem c7000 DDR2 Onboard Administrator with KVM Part Number : 456204-B21 Spare Part No.: 503826-001 Serial Number : XXXXXXXXXX UUID : xXXXXXXXX Manufacturer : HP Firmware Ver. : 4.11 Jan 16 2014 Hw Board Type : 2 Hw Version : B1 Loader Version: U-Boot 1.2.0 (Aug 31 2009 - 10:20:47) Serial Port: Baud Rate : 9600 Parity : None Data bits : 8 Stop bits : 1 Flow control: None
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-23-2018 01:01 AM
01-23-2018 01:01 AM
Re: BL460c G6 will not turn on and Led Health blink Red.
It may sound funny but you should check the CMOS battery on the blade mainboard. I had several servers that did not power up because that battery was dead.
If you have a voltmeter the battery should measure 3.0 to 3.2 Volts.
2.9V would still work but I recommend to replace it. If it is below that it may make problems...
When that red LED is blinking, what does the O-Administrator say about the balde? Does it show a red dot? If it says "power error" or "electronic fuse...." then your board is defective.
"If it seems illogical... you just don't have enough information"