- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: iLO configuration gone after enclosure powercy...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-22-2018 04:48 AM
тАО01-22-2018 04:48 AM
iLO configuration gone after enclosure powercycle
Hello community,
perhaps you have some ideas why this happens?
After switching off and turning the power on again for a c7000 enclosure the iLO configuration of 4 of 8 BL460c G6 blades is gone. This happens at every powercycle of the enclosure. The other 4 blades remember their iLO configuration.
Do you know ehere the iLO configuration is stored and if the configuration storage is battery powered and would i have to replace the battery? Or does anyone have a different explanation for this?
Thanks in advance for your input.
Best regards,
Tom
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-23-2018 12:49 AM
тАО01-23-2018 12:49 AM
Re: iLO configuration gone after enclosure powercycle
Did you check if the slot in the C7000 has EBIPA set ? (Enclosure Bay IP Addressing)
You can define all IP settings per slot in the OA configuration or set that function off for each slot. If EBIPA is active it will override the settings you made locally on the blade.
"If it seems illogical... you just don't have enough information"
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-23-2018 02:31 PM
тАО01-23-2018 02:31 PM
Re: iLO configuration gone after enclosure powercycle
Yes, i have EBIPA set for all blades. Yet the iLO looses its configuration like the Administrator password and the iLO hostname. Today i noticed that for that blade (which has a SB40c as partner device) it also looses the boot controller order. Might that be a hint what's wrong?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-24-2018 11:51 AM
тАО01-24-2018 11:51 AM
Re: iLO configuration gone after enclosure powercycle
Well that sounds like something is broken. In such a case I would set the iLO to factory defaults first, then update the iLO firmware, set your own password. If it still loses the information there is something wrong with that iLO flash memory chip (or something else). So you probably need a new mainboard.
Have you tried the blade in another slot? I mean just to see if it's an blade problem or the enclosure.
I had several DL380 G8 where the iLO stopped working. I replaced the flash chip (soldering required) and it worked again. Seems these chips lose information sometimes. Maybe a weakness because I never hat that n other models.
I don't know if the password and other settings are also stored in this chip but it's possible.
"If it seems illogical... you just don't have enough information"
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-24-2018 01:03 PM
тАО01-24-2018 01:03 PM
Re: iLO configuration gone after enclosure powercycle
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-25-2018 10:26 AM
тАО01-25-2018 10:26 AM
Re: iLO configuration gone after enclosure powercycle
Gen8...G6 different iLO's... I know. But the way how data is stored is certainly similar. I just wanted to point out that the flash memory could have a problem.
"If it seems illogical... you just don't have enough information"
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-25-2018 11:44 PM
тАО01-25-2018 11:44 PM
Re: iLO configuration gone after enclosure powercycle
I'm not exactly sure what the ILO2 does.
The ILO 4 has 4GB NAND flash memory on a chip to store settings, AHS log, Intelligent Provisioning etc.
This NAND flash can get corrupted if you run firmware 2.40 or earlier - search for ILO NAND to get the advisories how to solve this (how to format the NAND).
If the BIOS settings are also gone, this might be an empty battery in your G6.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-29-2018 01:29 PM
тАО01-29-2018 01:29 PM
Re: iLO configuration gone after enclosure powercycle
Thank you all very much for your advice. The blade does also loose the config in a different location of the enclosure. I am right now in the process of ordering a new mainboard to see if this works out. Your help is much appreciated!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-29-2018 01:32 PM - edited тАО01-29-2018 01:32 PM
тАО01-29-2018 01:32 PM - edited тАО01-29-2018 01:32 PM
Re: iLO configuration gone after enclosure powercycle
I am probably not going to try replacing the chip as of now as i need some soldering experience first, but would you happen to know which flash (that stores the config) i have to replace for a 460c G6? Thanks in advance ...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-29-2018 01:54 PM
тАО01-29-2018 01:54 PM
Re: iLO configuration gone after enclosure powercycle
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!