- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: How to remove 1 port in Virtual Connect Synerg...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-03-2019 12:15 AM
01-03-2019 12:15 AM
How to remove 1 port in Virtual Connect Synergy 1
Hello Everyone,
Current we have 4 port (2 port 1 BAY) & configuration is active-active , LACP on core switch.
Now we have need remove 1 port on 1 bay interconnect VC on Synergy system.
How impact with this action ? If we remove physical , what need we do it on config virtual connect ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-04-2019 07:23 AM
01-04-2019 07:23 AM
Re: How to remove 1 port in Virtual Connect Synergy 1
Hello,
Ok. You have 2 uplink ports from each ICM (ICM 3 and ICM 6) with Active-Active with LACP on core switch.
To change the uplink config from 2 port to 1 port from each ICM, you need to edit the uplink set on the Logical Interconnect Group (LIG).
Oneview --> Logical Interconnect Group --> Choose the Network LIG--> Edit --> Edit the "Uplink set"--> remove the uplink port which you wanted to remove --> Then click ok.
Once LIG is updated, you would need to perform Update from Group on the Logical Enclosure "Action " menu.
This would apply the configuration to VC module to use the single ports from both ICMs.
Once done, you need to update the LACP config on the core switch accordingly.
Ideally this should not cause any impact, however perform the changes during maintenance window.
Hope this helps..
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-07-2019 12:13 AM
01-07-2019 12:13 AM
Re: How to remove 1 port in Virtual Connect Synergy 1
Thank for your answer. More question "you would need to perform Update from Group on the Logical Enclosure "Action " menu" --> This action need downtime server for apply agian server profile ?
Thank so much.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-08-2019 04:27 PM
01-08-2019 04:27 PM
Re: How to remove 1 port in Virtual Connect Synergy 1
Hello,
The server downtime may not be required, since you are just removing the one uplink.. Other uplink should be active.
However, you might see network / storage disconnects depends on the uplink that you are removing it.
So better plan to do the same during planned maintenance window or during less load. so that impact would be lesser incase of any issue.
Hope this helps.