- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: Upgrade VCEM from 7.22 to 7.4.1 - firmware chi...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-20-2015 01:23 PM
05-20-2015 01:23 PM
Upgrade VCEM from 7.22 to 7.4.1 - firmware chicken or the egg?
Greetings,
I'm planning the upgrade to 7.4.1. This will be my first upgrade of VCEM. I have two c7000 enclosures managed by VCEM 7.2.2. My enclosure firmware level's are the following:
OA: 4.2.1
VCM: 4.10
Gen8 iLO: oldest is 1.5.1
I've been doing some RTFM'ing of HP docs and lots of firmware matrixes. The SIM/VCEM v7.4 installer seems to indicate that a minimum firmware level needs to exist on your modules prior to upgrading VCEM. I was of the mindset that I needed to get VCEM upgraded THEN do my firmware updates.
Anybody know that proper order of events?
Thanks for any "insight".
Ron
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-21-2015 03:50 AM
05-21-2015 03:50 AM
Re: Upgrade VCEM from 7.22 to 7.4.1 - firmware chicken or the egg?
Hi,
You may try the HP Virtual Connect Firmware Upgrade Steps and Procedures for more informaiton.
Regards,
Vijay
Views expressed herein are my personal opinion and are not the views of HPE
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-21-2015 10:00 AM
05-21-2015 10:00 AM
Re: Upgrade VCEM from 7.22 to 7.4.1 - firmware chicken or the egg?
Thanks for the reply I'll check it out.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-21-2015 03:47 PM
05-21-2015 03:47 PM
Re: Upgrade VCEM from 7.22 to 7.4.1 - firmware chicken or the egg?
This answers the chicken or egg question.
If Virtual Connect Enterprise Manager (VCEM) is in use, it must be at a revision that is compatible with the target VC firmware version prior to the VC firmware upgrade attempt. For the correct VCEM version, refer to the Virtual Connect Enterprise Manager Support section of this document.