- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: VMware 5 port profile settings and monitoring ...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-07-2013 08:02 PM
10-07-2013 08:02 PM
VMware 5 port profile settings and monitoring load
I Have 2 HP 7000 Blade chassis linked with ProLiant BL460c G7 blades running ESXi5 connected to the network with HP VC Flex Fabric 10gb/24-Port Modules.
The Blades have the following Port porfile config.
6 nic’s running on 6gb
2 HBA running on 4gb
Nic 1 ESX Console and Nexus 1000v – bay1 running at 1gb
Nic 2 ESX Console and Nexus 1000v – bay2 running at 1gb
Nic 3 Main VM Network – bay1 running at 3.5gb
Nic 4 Main VM network – bay2 running at 3.5gb
Nic 5 Vmotion – bay1 running at 1.5gb
Nic 6 Vmotion – bay2 running at 1.5gb
HBA 1 Fabric_A - Bay1 running at 4gb
HBA 2 Fabric_B – Bay2 running at 4gb
Questions
1. Is this the Best or Recommened setup for the ESXi Hosts in the HP chassis?
2. How can I monitor and see if one interface is under more load than the others?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-08-2013 07:55 PM
10-08-2013 07:55 PM
Re: VMware 5 port profile settings and monitoring load
1) You can monitor the performance of individual FlexNICs in the profile using a 3rd party SNMP based management tool. The new MIBs have been on the website for 6+ months at least.
2) You can now allow individual FlexNICs to burst. So your 1.5Gb for vMotion, you can now set a Max speed of 5Gb and this will allow the vMotion NICs to burst to 5Gb, get the vMotion done quickly and drop back to idle. Then that 1.5 can be used by other FlexNICs like for the VMs when vMotion is idle.
Aside from that, I've found the easiest way to monitor interface utilization is actually from the VMware side. It gathers a lot of these metrics already and you can see if a particular NIC is getting close to its max you have set in the profile.
You only need to monitor TRANSMIT Bandwidth though because VC does not limit Receive bandwidth. By the time the packet reaches the NIC, which is where the bandwidth throttling happens, it doesn't make a lot of sense to drop it and make the sender retransmit.
All that aside, I don't see anything glaringly wrong with your config. We have a ESXi 5 on FlexFabric Guide and your numbers are pretty close to the ones in there.