- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: "Invalid SOAP response" when trying to create ...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-10-2011 05:42 AM
03-10-2011 05:42 AM
"Invalid SOAP response" when trying to create vc domain
Hi,
I'm installing two VC switches to replace some GbE2c's in our enclosure. I have done this before on another enclosure and not had any problems but this time I get an "invalid SOAP response" 5-10 minutes after trying to import the enclosure and create the domain.
Has anyone else experienced this?
I have tried restarting the onboard administrator and the virtual connect switches but keep getting the same thing.
VC firmware is 3.15
OA firmware is 3.20
Cheers
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-10-2011 09:06 AM
03-10-2011 09:06 AM
Re: "Invalid SOAP response" when trying to create vc domain
I have not seen this error in the forums that I watch. I will see what i can find out.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-14-2011 10:37 AM
03-14-2011 10:37 AM
Re: "Invalid SOAP response" when trying to create vc domain
My experts have not seen this error as well:
"Since it is OA version 3.20 I’m not aware of any SOAP errors on the OA."
I would suggest you log a support call.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-16-2011 02:41 AM
03-16-2011 02:41 AM
Re: "Invalid SOAP response" when trying to create vc domain
thanks for looking anyway.
I have logged a support call but the advice from HP has not been that helpful.
I suspect a hardware issue as I am unable to force an upgrade (to the same version) on the switch. I will try to replace the hardware and see if I get the same problem
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-16-2011 04:50 AM
03-16-2011 04:50 AM
Re: "Invalid SOAP response" when trying to create vc domain
I am also getting the fault at the moment with the same configuration
Any ideas
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-16-2011 08:44 AM
03-16-2011 08:44 AM
Re: "Invalid SOAP response" when trying to create vc domain
I have seen this happen when the enclosure fails to import correctly during the vc first time wizard. You can get past that section but then you start seeing the SOAP errors when trying to create the domain.
When you run the vc wizard make sure this part of the process completes.
Try reimporting the enclosure?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-16-2011 08:48 AM
03-16-2011 08:48 AM
Re: "Invalid SOAP response" when trying to create vc domain
Sorry, missed the important bit. I fixed this by stripping the enclosure down to just one VC module and re-running the vc wizard.
The enclosure imported ok and i could create the domain. I then added the second module and was able to match up firmware versions with vcsu.