- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Comware Based
- >
- 10508 Comware v7 fabric error
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-29-2020 06:04 AM
тАО01-29-2020 06:04 AM
10508 Comware v7 fabric error
Hi there...
I have a customer where I just installed an HPE 10508 chassis, running the latest firmware version of v7. In this next weekend I am going to add an slave member, forming the IRF Stack that has been previiously configured.
The first chassis is running for the last 10 days without problems, while the second rack is being fixed, where the second chassis will be installed. But yesterday a strange error started to appear in the log, without any clue of which could be the root cause:
% Jan 28 12: 06: 03: 519 2020 ESACSE_DC_CORE DEV / 4 / DEV_FAULT_TOOLONG: Card in chassis 1 slot 10 is still in Fault state for 10200 minutes.
The slot 10 refers to the first fabric card. This message was repeated every 60 minutes until this morning, when we pulled out the card and inserted it again, back to normal operation.
As I said before, there is no clue of what could be the root cause of this alarm in the log - just the error itself. I am not sure if I can swap the card with another fabric from the second switch, which is already configured, so I didn't made any offline test with the card. I know that the control plane and data plane runs separately in MPU and the fabric cards, but I am not sure if I could swap cards from different switches that are already configured.
Any idea of what is this error? I could not find any document referred to somtehing like that.
Thanks in advance for any help.
Fred Mancen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-29-2020 05:25 PM
тАО01-29-2020 05:25 PM
Re: 10508 Comware v7 fabric error
It looks like a Device Management Warning message (with a Severity Level of 4 which means "Warning") and recommended actions are: reboot the card or, If the problem persists, contact the HPE Support. Not much more about possible causes.
Wasn't able to find a reference exactly about the HPE 10500 Switch series...the nearest one reference (note that is common to Comware 7 NOS) references to HPE 5950 Switch series (see here sheet 304 "Device Messages" Chapter).
I'm not an HPE Employee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-30-2020 04:59 AM
тАО01-30-2020 04:59 AM
Re: 10508 Comware v7 fabric error
Hi Parnassus.
The HPE support just called me, there are an alarm with the health level of the primary MPU in the display diagnostic output:
==== display hardware internal diag health information chassis 1 slot 4 ====
Health Error List :
Fwd Check Fail
Hg Monitor Check Fail
Health Error lever :2
This means that a problem with the sync among the cards and the MPU can be the root cause of these events. Today we will perform some tests with the MPU and I will let you know, later.
Fred Mancen