- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Comware Based
- >
- 2426 pwr: ports go inactive
Comware Based
1753867
Members
7553
Online
108809
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-23-2009 01:45 PM
09-23-2009 01:45 PM
2426 pwr: ports go inactive
Ports 3,6,9,20,23,24 show 'inactive' in the switch summary.
The same ports plus 11,12,21 show the 'state' as 'discarding' instead of 'forwarding' under spanning tree. There is no setting for the spanning tree state (in the GUI).
Some of the ports have computers connected that worked until yesterday, others are not used. I have disabled and enabled the port state but no go.
I don't have much time on switches in general and 3COM in particular but I know that if I bounce the switch it will be fine. Any way to fix without inconveniencing users?
Thanks for any help.
3C16491
Software ver. 1.0.1.17
BootROM ver. 1.0.0.4
Hardware ver. R01
The same ports plus 11,12,21 show the 'state' as 'discarding' instead of 'forwarding' under spanning tree. There is no setting for the spanning tree state (in the GUI).
Some of the ports have computers connected that worked until yesterday, others are not used. I have disabled and enabled the port state but no go.
I don't have much time on switches in general and 3COM in particular but I know that if I bounce the switch it will be fine. Any way to fix without inconveniencing users?
Thanks for any help.
3C16491
Software ver. 1.0.1.17
BootROM ver. 1.0.0.4
Hardware ver. R01
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-23-2009 03:50 PM
09-23-2009 03:50 PM
Re: 2426 pwr: ports go inactive
Hi.
The discarding status means that the port has no one device attached or a port blocked by the STP.
Try to set up the ports where the workstations are connected as edged ports. Regarding the inactive status you mentioned, actually I didn't remember what could it be.
Regards
The discarding status means that the port has no one device attached or a port blocked by the STP.
Try to set up the ports where the workstations are connected as edged ports. Regarding the inactive status you mentioned, actually I didn't remember what could it be.
Regards
Regards,
Fred Mancen
Fred Mancen
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP