- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Comware Based
- >
- Re: 2910al-24 - Programming Next Hop
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-01-2012 02:49 PM
02-01-2012 02:49 PM
2910al-24 - Programming Next Hop
I have a HP 2910al-24 switch that has an Avaya PBX connected to it. The switch is connected to another switch that is connected to our Lan and a router that goes out to our SIP provider. When the PBX was set up, they gave it the default gateway to our Lan so the PBX could connect via IP to their facility where they monitor and remote in for maintenance. This all works.
What we need to do is be able to send SIP traffic to the router that connects to our SIP provider but I can't figure out how (if it's possible) to tell the 2910 to route the SIP traffic tot he router.
Our Lan network is 192.168.50.x /23 network
Lan gateway is 192.168.50.1
The router IP address is 192.168.51.33
2910al IP is 192.168.51.148
SIP traffic IP is 10.250.0.x
Can the 2910 be programmed to send 10.250.0.x SIP from the PBX to the router at 192.168.51.33?
If I put in a rule in the gateway that says anything coming from the PBX gets routed to 192.168.51.33 it works. But then that means all of the SIP traffic will flow over my network, to my gateway and back to the PBX. I don't want to do that.
The networking people with the company that installed the PBX said we have to get a CISCO 3750 switche and do a bunch of changes to our network to get it to work. Since the Avaya won't let you put in two gateways that may be what will have to be done, but if I can get the 2910 to work, I'd rather do it that way since it seems all I need is a simple route in the 2910 to point 10.250.0.x traffic to the 192.168.51.33 port of the router.
Thanks for any help on this.
Mike
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-06-2012 04:12 PM
02-06-2012 04:12 PM
Re: 2910al-24 - Programming Next Hop
Hi,
The feature you are looking for is called Policy Based Routing - where you can select a specific type of traffic to forward to a next-hop.
Unfortunately, the 2910al is for basic routing, so it does not support this function. From the HP switching side, it is supported on the 5400zl with v2 modules as well as the 5500-EI series stackables. These options are probably more economical than a 3750.
Best of luck,
RK
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-18-2012 10:54 PM
02-18-2012 10:54 PM
Re: 2910al-24 - Programming Next Hop
You could actually put in a static route into the 2910 for the 10.250.0.0/24 subnet. Then all traffic destined for 10.25.0.x would go to that destination instead. All other traffic would go to the default router (192.168.50.1) eg:
ip route 10.250.0.0/24 192.168.51.33
The HP 3800 is analogous to the 3750.
BTW, the 2910, 3800, 5400zl used to be call "E Series", and this post should really be in the E Series area!