cancel
Showing results for 
Search instead for 
Did you mean: 

5500 and Radius

 
sean_2
Occasional Contributor

5500 and Radius

I have a 5500 that I am trying to connect to a Microsoft IAS Radius server. However, the connection does not work.



Has anyone succesfully connected a 5500 to a Radius server?





This is the configuration set up, the log on the Microsoft IAS and the debug radius on the switch:





sysname SW1

#

undo password-control aging enable

undo password-control length enable

undo password-control history enable

password-control login-attempt 3 exceed lock-time 120

#

local-server nas-ip 127.0.0.1 key 3com

#

domain default enable test2

#

igmp-snooping enable

#

radius scheme system

radius scheme test

server-type extended

primary authentication 172.30.4.4 1645

key authentication 3com

user-name-format without-domain

#

domain system

domain test2

authentication radius-scheme test

#

local-user admin

service-type telnet terminal

level 3

local-user manager

password simple manager

service-type telnet terminal

level 2



…



user-interface aux 0 7

authentication-mode scheme

user-interface vty 0 4

authentication-mode scheme

#











======================================================================================================









EVENT 5050 – IAS



A LDAP connection with domain controller complete02.complete.ie for domain COMPLETE is established.



For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.







EVENT 1 – IAS



User javier.robles was granted access.

Fully-Qualified-User-Name = complete.ie/Complete/Departments/Engineering/Users/Javier Robles

NAS-IP-Address = 172.30.2.190

NAS-Identifier = 0012a9a2b802

Client-Friendly-Name = Test

Client-IP-Address = 172.30.2.190

Calling-Station-Identifier = 0000-0000-0000

NAS-Port-Type = Ethernet

NAS-Port = 268439553

Proxy-Policy-Name = Use Windows authentication for all users

Authentication-Provider = Windows

Authentication-Server =

Policy-Name = Connections to other access servers

Authentication-Type = PAP

EAP-Type =



For more information, see Help and Support Center at























======================================================================================================











*0.191453 5500G-EI RDS/8/DEBUG:- 1 -Recv MSG,

*0.191579 5500G-EI RDS/8/DEBUG:- 1 -Send attribute list:

*0.191649 5500G-EI RDS/8/DEBUG:- 1 -













*0.192109 5500G-EI RDS/8/DEBUG:- 1 -









*0.192429 5500G-EI RDS/8/DEBUG:- 1 -Send: IP=, UserIndex=, ID=, RetryTimes=, Code=, Length=

*0.192578 5500G-EI RDS/8/DEBUG:- 1 -Send Raw Packet is:

*0.192649 5500G-EI RDS/8/DEBUG:- 1 -

01 00 00 77 00 00 59 f8 00 00 34 21 00 00 77 11

00 00 66 76 01 0f 6a 61 76 69 65 72 2e 72 6f 62

6c 65 73 02 12 74 8e 10 67 17 26 a8 0c 72 65 26

bd 60 16 c6 94 04 06 ac 1e 02 be 20 0e 30 30 31

32 61 39 61 32 62 38 30 32 05 06 01 00 10 01 3d

06 00 00 00 0f 06 06 00 00 00 01 0e 06 ac 1e 02

be 1f 10 30 30 30 30 2d 30 30 30 30 2d 30 30 30

30 08 06 ac 1e 02 42



*0.193169 5500G-EI RDS/8/DEBUG:- 1 -Recv MSG,

*0.193289 5500G-EI RDS/8/DEBUG:- 1 -Receive Raw Packet is:

*0.193359 5500G-EI RDS/8/DEBUG:- 1 -

02 00 00 40 3a d1 42 01 f4 cc 4b c1 e3 cb a7 e1

47 95 75 5c 07 06 00 00 00 01 06 06 00 00 00 02

19 20 53 f0 06 8a 00 00 01 37 00 01 ac 1e 04 04

01 c9 78 c0 cb f2 a2 e0 00 00 00 00 00 00 00 3d





*0.193679 5500G-EI RDS/8/DEBUG:- 1 -Receive:IP=,Code=,Length=

*0.193779 5500G-EI RDS/8/DEBUG:- 1 -









2 REPLIES
rlw
Occasional Visitor

Re: 5500 and Radius

Hello !



Your config from the 5500 does not state that you enable 802.1x on your interfaces. There is a advanced configuration guide on the 3com support site , if you search for the 5500 documentation . this is very useful.

Pls check, that your 5500 is running latest firmware !



Best regards

Robert

aydinkocak
Advisor

Re: 5500 and Radius

Hello;

I am sending tested 5500 config with Microsof IAS :

and than enable dot1x system wide and interface wide.

--------------------------------------

radius scheme turkom

server-type standard

primary authentication 192.168.1.250

primary accounting 192.168.1.250

key authentication ******

key accounting ******

user-name-format without-domain

#

domain turkom

scheme radius-scheme turkom

vlan-assignment-mode string

#

domain default enable turkom

-------------------------------



What is your authentication protocol EAP-MD5,

EAP-TLS, etc.. ?

AYDIN KOCAK,

3COM Enterprise LAN Expert ( Pre & Post Sales),

TippingPoint Security Engineer,

CCNA,CCDA, CCIE R&S Written
AYDIN KOCAK,

3COM Enterprise LAN Expert ( Pre & Post Sales),

TippingPoint Security Engineer,

CCNA,CCDA, CCIE R&S Written