- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Comware Based
- >
- Re: 5500G-EI IPv6
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-18-2016 07:27 AM
тАО04-18-2016 07:27 AM
5500G-EI IPv6
Hello,
I want to use IPv6 on 10Vlans. But when I set the secend IPv6 address the switch allways says:
[SWITCH] interface vlan-interface 10
[SWITCH-Vlan-interface10] ipv6 address fc00:0:0:0:f010::1 64
Error: The number of IPV6 interfaces has reached the maximum limit!
What is my fault? I have added the configuration in the file "switch_config.txt".
Switch typ: 3Com Switch 5500G-EI PWR 48-Port Software Version 3Com OS V3.03.02s168p22
Thank you and have a nice day!
Samuel
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-13-2016 08:16 AM
тАО06-13-2016 08:16 AM
Re: 5500G-EI IPv6
Hi.
interface Vlan-interface100 ip address 10.64.0.253 255.255.255.0 ipv6 address FC00:0:0:F100::1/64 ipv6 address FC00:0:0:FB00::1/64
I don't work with IPv6 on my interfaces yet but, why did you put two networks on the same VLAN interface?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-30-2016 05:32 AM
тАО11-30-2016 05:32 AM
Re: 5500G-EI IPv6
Hello, I have the same problem. Same software version V3.03.02s168p22.
Manual says I have to enable IPv6 by command ipv6 in system-view, but there is no such command:
[5500G-EI]ipv6 ? host Add/Remove a host name and its IP address to the IPv6 host name table icmp-error Specify ICMPv6 configuration information nd IPv6 interface neighbor discovery subcommands neighbor IPv6 neighbor cache entries route-static Establish static route [5500G-EI]ipv6 ^ % Incomplete command found at '^' position.
Maybe this problem is only in this software version, but I do not see anything in changelog about this issue.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-08-2017 09:30 AM
тАО01-08-2017 09:30 AM
Re: 5500G-EI IPv6
What is the HPE device/model id of your switch (such as JC102A or similar)?
According to the manual for 5500 (R2205) you enable ipv6 by:
> system-view
> ipv6
> exit
> reboot
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-12-2017 08:34 AM
тАО01-12-2017 08:34 AM
Re: 5500G-EI IPv6
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-12-2017 09:11 AM
тАО01-12-2017 09:11 AM
Re: 5500G-EI IPv6
Probably you should - if permitted on your 3Com Switch model (probably with HP Product Number JF553A) - first (re)brand your 3Com into HPE then update it to latest available software version HPE released for that model.
I'm not totally sure you can on the old 3Com SuperStack 4 5500 (see here).
Try at CLI the command brand hp to see what output your switch shows (if any), examples here.
Eventually you can't HP (re)brand try to look here for latest available Firmware: it looks like it isn't Comware (5) based. Here for documentation.
I'm not an HPE Employee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-17-2017 08:11 AM
тАО01-17-2017 08:11 AM
Re: 5500G-EI IPv6
Hello parnassus,
thank you, I have read the documentation you posted and tried to find more. This 5500G-EI 3com apparently can not be upgraded into H3C or HPE as it has not enough memory.
So for IPv6 routing I will need newer hardware, probably HPE 5500 24G SFP HI (JG543A) or HPE 5500 24G SFP EI (JD374A)
Henly