- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Comware Based
- >
- Re: Configuring SFlow on HP(3com) A5500 JD374A
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Latin America
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-12-2014 06:14 AM
09-12-2014 06:14 AM
Configuring SFlow on HP(3com) A5500 JD374A
Hello
I'm trying to configure this device to send sflow messages to an sflow collector at 192.168.5.63
This is my configuration at the moment can anyone point out the issue here as im not getting any sflow traffic.
Thanks
#
sflow agent ip 192.168.5.254
sflow collector 1 ip 192.168.5.63 description "CLI Collector"
#
#
interface Vlan-interface105
description Servers vlan105
ip address 192.168.5.251 255.255.255.0
vrrp vrid 5 virtual-ip 192.168.5.254
vrrp vrid 5 authentication-mode simple dental12
packet-filter 3305 inbound
#
#
interface GigabitEthernet1/0/1
port link-mode bridge
description link to edge1
port link-type trunk
port trunk permit vlan 1 101 to 104 106 to 107 130 210
stp instance 1 port priority 64
sflow sampling-rate 10000
sflow flow collector 1
sflow counter interval 20
#
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-12-2014 09:21 AM
09-12-2014 09:21 AM
Re: Configuring SFlow on HP(3com) A5500 JD374A
What happens when you try a "display sflow"? Does it show you the configuration and status?
The sflow collector will transmit on port 6343 by default. Could the port be blocked on your network? You can change the port, if desired, on the sflow collector command in the range of 1 to 65535.
Also, there is a note in the documentation that the 5500 SI switch does not support the "port link-mode bridge" command. If you are using that switch, that may be an issue.
David
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
10-23-2014 02:27 PM
10-23-2014 02:27 PM
Re: Configuring SFlow on HP(3com) A5500 JD374A
If you are on another switch and needs to pass through the trunk it would´t be possible due the trunk dont have the vlan 105 in it. But if not , maybe if you set sflow source [Your IP] the data should appears.
thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
12-18-2017 05:17 AM
12-18-2017 05:17 AM
Re: Configuring SFlow on HP(3com) A5500 JD374A
How can I disable sflow on an HP-5500 SI
Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP