- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Comware Based
- >
- Error Firmware 3Com Baseline 2924
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-26-2013 04:36 PM - last edited on 06-30-2013 07:31 PM by Maiko-I
06-26-2013 04:36 PM - last edited on 06-30-2013 07:31 PM by Maiko-I
Error Firmware 3Com Baseline 2924
Hello friends I have a problem with a switch 3com Baseline Switch 2924 - SFP Plus (3CBLSG24), the detail is that when you start sends this error
Network Switch based on 88E6218 with ARM946E-S.
64MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.
Preparing to decompress ...
100% Image in address: 0x0 - Check Sum Error!
------ Performing the Power-On Self Test (POST) ------
UART Channel Loopback Test ........................ PASS
Testing the System SDRAM .......................... PASS
Checksum Test ............................... PASS Boot1
Boot2 Checksum Test ............................... FAIL
Flash Image Validation Test ....................... PASS
BOOT Software Version 1.0.0.14 Built 17-May-2007 12:35:42
Network Switch based on 88E6218 with ARM946E-S.
64MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.
Preparing to decompress ...
100%
This process is repeated constantly and does not load the switch, I looked on google and found nothing.
I hope your help, thanks.
P.S. This thread has been moved from Switches, Hubs, Modems (Legacy ITRC forum) to Comware-Based. - HP Forum Moderator
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-04-2014 04:39 AM
06-04-2014 04:39 AM
Re: Error Firmware 3Com Baseline 2924
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-06-2014 06:03 AM
06-06-2014 06:03 AM
Re: Error Firmware 3Com Baseline 2924
Did you try contact the support to have this unit replaced?
Otherwise I think there is a keycombo you can press when connected through serial cable to the device to halt its bootprocess and from there be able to upload a new firmware (dont forget to update the bootrom aswell if 3com uses that).