Comware Based
1748094 Members
5868 Online
108758 Solutions
New Discussion

Re: HP 5130 - how do I change the password for the admin user

 
danielb21think
Occasional Advisor

HP 5130 - how do I change the password for the admin user

We have an HP5130 switch and tried to login to the web interface with:

Username: admin

Password: as previously setup

Verify code: as per that on the page

This would not allow us to login.

We have access via a serial connection and the below commands were run:

1/ system-view   - to change to system view.

2/ local-user admin  - I believe to switch to that user.

3/ password simple newpassword   - to set the new password as a plain text password.

4/ service-type https - to specify the service type

5/ authorization-attribute user-role network-operator

This does not appear to change the password, we had to follow this to create a new user, which allows us to login to the web interface as required.

I have not been able to find after much searching how to change the password for the user 'admin'. 

If you are able to advise that would be appreciated.

Many thanks

Daniel

10 REPLIES 10
johnk3r
Respected Contributor

Re: HP 5130 - how do I change the password for the admin user

Hello!

Can you access the console with another user? Post the output of the command below:

dis local-user

 

**************************************
ATP FLEXNETWORK V3 | ACSA
HP-Browniee
Respected Contributor

Re: HP 5130 - how do I change the password for the admin user

Hello

To change the password for the admin user, it should be like you described.

Maybe try to change the authorization-attribute or the service type.

 

Kind regards

danielb21think
Occasional Advisor

Re: HP 5130 - how do I change the password for the admin user

Hi johnk3r,

Thanks for your reply.

Output of dis local-user for this user is:

Device management user admin:
State: Active
Service type: SSH/HTTP/HTTPS
User group: system
Bind attributes:
Authorization attributes:
Work directory: flash:
User role list: network-admin, network-operator

johnk3r
Respected Contributor

Re: HP 5130 - how do I change the password for the admin user

Strange ... it's a setup right.

Does both HTTP and HTTPS access have the same problem ?

**************************************
ATP FLEXNETWORK V3 | ACSA
danielb21think
Occasional Advisor

Re: HP 5130 - how do I change the password for the admin user

Hi johnk3r,

Thanks for your continued help.

Yes, both http and https have the issue.

Before I posted in the first place to the forum I created another user so I could login again via the web interface by the method I described in my opening message and I can then see how to change the password for the user 'admin' in the web interface, if I do this will it cause the switch to reboot to apply the change?

Many thanks

Daniel

 

johnk3r
Respected Contributor

Re: HP 5130 - how do I change the password for the admin user

Hello.

No, it is not necessary to reboot the switch after a configuration.

**************************************
ATP FLEXNETWORK V3 | ACSA
danielb21think
Occasional Advisor

Re: HP 5130 - how do I change the password for the admin user

Hi johnk3r,

Thanks for your prompt response, appreciated.

I'll get it done that way.

Thanks

Daniel

danielb21think
Occasional Advisor

Re: HP 5130 - how do I change the password for the admin user

Hi johnk3r,

I tried yesterday to update the password for the user 'admin' via the web interface (logging in using the user 'admin2'). Initially it advised this was not allowed because of the role, I updated it so the user admin2 is now:

Device management user admin2:
State: Active
Service type: HTTPS
User group: system
Bind attributes:
Authorization attributes:
Work directory: flash:
User role list: network-admin, network-operator

I logged back in to the web interface as admin2 and navigated:

Device (left hand menu) > Administrator > Administrator (on the next page) > selected admin (ticked it) and then click on 'edit' at the bottom.

Input the new password, 10 characters or more as minimum password length is set, clicked 'Apply' and it reports on that page in red 'operation failed'.

Many thanks

Daniel

 

 

 

danielb21think
Occasional Advisor

Re: HP 5130 - how do I change the password for the admin user

Hi johnk3r,

Issue resolved by:

1/ Logging in with the additional user via the web interface that I created on the cli.

2/ Deleting user 'admin'

3/ It would not allow me to re-add that user via the web interface, I had to do this as per my first post via the cli.

I learnt if the user requires an additional role simply just repeat the same line you used to give them the first role and change it to what you need it to be.

4/ First login after creation it will prompt you to change the password (I used 12 characters as the 10 character minimum length is enabled).

I am now able to login as required.

Thank you for your help and I hope this helps somebody else.

Thanks

Daniel