- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Comware Based
- >
- Re: HPSwitch & 3Com switch PBDU dismatch.
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-13-2012 06:11 PM
08-13-2012 06:11 PM
HPSwitch & 3Com switch PBDU dismatch.
Hi,
I had a customer, when he connect from Switch HP5500 to 3com4526, the port at 3Com4526 site will auto disable during operation. I check on the log on 3Com switch display as below:
#Apr 24 22:59:46:714 2000 3C4526-L4#2 MSTP/2/LGEXP:- 1 -1.3.6.1.2.1.17.0.1(newRoot): I am the root of instance 0 now!
%Apr 24 22:59:46:897 2000 3C4526-L4#2 MSTP/3/BPDUFORMATERROR:- 1 -Port GigabitEthernet1/0/28 received different format of BPDU packets continually! Shut down it in order to avoid broadcast
#Apr 24 22:59:47:401 2000 3C4526-L4#2 L2INF/2/PORT LINK STATUS CHANGE:- 1 -
Trap 1.3.6.1.6.3.1.1.5.3(linkDown): portIndex is 4227841, ifAdminStatus is 2, ifOperStatus is 2
Both side port been configure it trunk as below:
HP5500 switch:
interface GigabitEthernet1/0/19
port link-mode bridge
port link-type trunk
port trunk permit vlan all
broadcast-suppression pps 3000
undo jumboframe enable
stp edged-port enableinterface
3Com switch:
interface GigabitEthernet1/0/28
stp edged-port enable
port link-type trunk
port trunk permit vlan 1 106 to 107
What does it mean by the log? Could anyone assist me on this matter, thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-14-2012 11:11 AM
08-14-2012 11:11 AM
Re: HPSwitch & 3Com switch PBDU dismatch.
It means the 3com doesn't understand the kind of spanning tree protocol the 5500 is using (in the top line of display stp output). This might potentially cause a forwarding loop, and network storm, so it shuts down the port.
You could downgrade the spanning tree protocol to an earlier version (e.g. to RSTP). Or you might get later firmware for the 3com, from ther HP support site.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-11-2012 01:31 AM
10-11-2012 01:31 AM
Re: HPSwitch & 3Com switch PBDU dismatch.
I had found the root cause few month ago and it was a big mistake! That is because the HP5500 switch STP feature don't enable. It was new switch come with no stp enable, i never thought stp is disable by default.
I enable stp then the problem sloved. Thanks for your reply.