Comware Based

Help with Lab Please

 
prodigy811
Frequent Advisor

Help with Lab Please

Hi there,

 

I have a simple lab set up. I have a DC either side and they are connected via Route Agg link. I have a SVI on both sides with another switch connected so that both SVI's are up. SVI IP on 1 side is 192.168.10.1/24 other side 192.168.10.2/24. I have Statics set up on both sides etc. The Point to point link (RAGG) is 172.21.99.1 and .2.

Here is the strange thing; when I have both SVIs up I can only ping Nort to South..So switch I am on can ping the switch directly connected not over the RAGG point to point obviously. I cannot ping the other switch's SVI accross the RAGG. This is the same on the other DC side. Here is the strange thing; when I shut down an SVI on 1 side the switch in the other DC can ping accross fine. So basically my lab with only work accross the point to point links if 1 of the SVIs are shutdown.

Here is my statics,

DC1;

 

dis current-configuration | i static
ip route-static 10.60.94.0 24 172.21.99.2
ip route-static 10.60.105.0 24 172.21.99.2
ip route-static 172.21.9.2 32 172.21.99.2
ip route-static 192.168.10.0 24 172.21.99.2

DC2;

ip route-static 10.60.80.0 24 172.21.99.1
ip route-static 10.60.98.0 24 172.21.99.1
ip route-static 10.60.150.0 24 172.21.99.1
ip route-static 172.21.9.1 32 172.21.99.1
ip route-static 192.168.10.0 24 172.21.99.1

Obviously I am just concentrating on the 192.168.10/24 address at the moment.

DLake Topology.PNG

Any help much appreciated

6 REPLIES 6
akg7
HPE Pro

Re: Help with Lab Please

Hello,

Which SVI you are shutting down and what is the IP address on it?

Is this happening for all SVI's or only for a particular SVI?

Can try to add a default route on both DC and check?

Thanks!

I am an HPE Employee

Accept or Kudo

prodigy811
Frequent Advisor

Re: Help with Lab Please

Hi there,

 

At present I am only working with the 192.168.10 (Test) range. When I shut down SVI Int vlan 10 (192.168.10.1) I am able to ping the 192.168.10.2 and 192.168.10.10 oposite DC. I have statics in place on both sides,(My default routes) please see my previous posts. It is a weird one.

Thanks for your help by the way, if you can think of anything else please let me know.

prodigy811
Frequent Advisor

Re: Help with Lab Please

Any help much appreciated

akg7
HPE Pro

Re: Help with Lab Please

Hi @prodigy811 ,

Thank You for sharing details.

I will check in LAB and I willl update you by tomorrow.

Thanks!

I am an HPE Employee

Accept or Kudo

akg7
HPE Pro

Re: Help with Lab Please

Hello @prodigy811 ,

I have tried to replicate the issue but I haven't face such issue when one SVI is down and its started reaching to other switches.

May be your device has more config.

1. Can you please share display ip routing-table from all 4 devices?

2. Please share interface level config from all devices which includes route-aggregation config as well.

Thanks!

I am an HPE Employee

Accept or Kudo

prodigy811
Frequent Advisor

Re: Help with Lab Please

Hi there,

Very sorry for late reply. I am actually off work and once back ill update you with what you requested. Many many thanks for all your help!!