- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Comware Based
- >
- Re: JG372A - SecBlade III questions on installatio...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-31-2015 01:50 PM
03-31-2015 01:50 PM
JG372A - SecBlade III questions on installation
Ok, since this goes in a switch, obstensively uses comware, and I couldn't find another forum, figured I'd start asking here first.
1. The "front" of the card as 2 GE interfaces and 2XGE ports. Both labeled 1 and 2 (combo). However when I look at the inventory, the car tells me it has the following:
[FIXED PORT] GE0/1(Hardware)Ver.A, (Driver)1.0, (Cpld)4.0
[FIXED PORT] GE0/2(Hardware)Ver.A, (Driver)1.0, (Cpld)4.0
[FIXED PORT] XGE0/1(Hardware)Ver.A, (Driver)1.0, (Cpld)4.0
[FIXED PORT] XGE0/2(Hardware)Ver.A, (Driver)1.0, (Cpld)4.0
[FIXED PORT] XGE0/3(Hardware)Ver.A, (Driver)1.0, (Cpld)4.0
[FIXED PORT] XGE0/4(Hardware)Ver.A, (Driver)1.0, (Cpld)4.0
Any idea which port is which on the front? I'm assuming the XGE marked "2" is the XGE0/2 port... however...
2. I can't connect to the XGE port as the standard SFP+ units I use (JD092B) and (JD095C) both come up with
%Apr 1 04:20:14:448 2015 HP OPTMOD/4/MODULE_IN:
GigabitEthernet0/2: The transceiver is UNKNOWN_SFP.
---
Since I seem to be in documentation hell, first off do I even have the correct SPF+ part numbers for this card? Everything else we have (all the other A7500 cards, A5800s, A6602s, etc) all use the two SPF+ numbers above (first is optical, second is hardwired).
It would be really really sad if they use different GBICs than everything else in the H3C lineup use...
---
Second big question... If XGE 0/1 and XGE 0/2 are the two ports on the front of the card, where the heck are XGE 0/3 and XGE 0/4 located?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-31-2015 02:50 PM
03-31-2015 02:50 PM
Re: JG372A - SecBlade III questions on installation
The ports on the front of the module are gig combo ports, meaning you can use either the RJ45 or the SFP port but not both at the same time. They are Gig only.
The 4 10Gig ports connect to the backplane of the switch. You use VLANs to plumb them where every you need to.
Does that help?
Regards,
Eric
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-31-2015 04:59 PM - edited 03-31-2015 08:15 PM
03-31-2015 04:59 PM - edited 03-31-2015 08:15 PM
Re: JG372A - SecBlade III questions on installation
Ah, so those are SFP, not SFP+ ports... ok... so the "internal" ports, how do you plumb those to the A7500 internally? Of course as far as I can tell, there is no documentation to find (have been looking for the last few hours). Are they supposed to show up on the switch backplane somehow?
Looking closer at the A7500, I now see:
[SC9-CORE-SW]display device manuinfo chassis 1
Slot 7:
DEVICE_NAME : HP 10500/11900/7500 20Gbps VPN FW Mod JG372A
DEVICE_SERIAL_NUMBER : CN45------
MAC_ADDRESS : NONE
MANUFACTURING_DATE : 2014-05-24
VENDOR_NAME : HP
along with the following interfaces:
1/7/0/1
1/7/0/2
1/7/0/3
1/7/0/4
So just experimenting, I did the following:
interface Ten-GigabitEthernet1/7/0/1
port link-mode bridge
description SECBLADE III port ???
port link-type trunk
undo port trunk permit vlan 1
port trunk permit vlan 11
and on the SecBLADE III I did:
interface Ten-GigabitEthernet0/1.11
vlan-type dot1q vid 11
ip address 172.24.194.8 255.255.255.192
however that doesn't seem to work... other suggestions on how to "wire" these together?
Marcos
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-01-2015 04:18 PM
04-01-2015 04:18 PM
Re: JG372A - SecBlade III questions on installation
Depending on how the rest of VLAN 11 is configured that should work.
Here is a link to the getting started guide: http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/action.process/public/psi/manualsDisplay/?sp4ts.oid=4181066&javax.portlet.action=true&spf_p.tpst=psiContentDisplay&javax.portlet.begCacheTok=com.vignette.cachetoken&spf_p.prp_psiContentDisplay=wsrp-interactionState%3DdocId%253Demr_na-c03941520%257CdocLocale%253Den_US&javax.portlet.endCacheTok=com.vignette.cachetoken