- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Comware Based
- >
- Networking shows DOWN -- How to bring up?
-
- Forums
-
Blogs
- Alliances
- Around the Storage Block
- Behind the scenes @ Labs
- HPE Careers
- HPE Storage Tech Insiders
- Infrastructure Insights
- Inspiring Progress
- Internet of Things (IoT)
- My Learning Certification
- OEM Solutions
- Servers: The Right Compute
- Shifting to Software-Defined
- Telecom IQ
- Transforming IT
- Infrastructure Solutions German
- L’Avenir de l’IT
- IT e Trasformazione Digitale
- Enterprise Topics
- ИТ для нового стиля бизнеса
- Blogs
-
Quick Links
- Community
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Contact
- Email us
- Tell us what you think
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Enterprise.nxt
- Marketplace
- Aruba Airheads Community
-
Forums
-
Blogs
-
InformationEnglish
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
07-11-2018 06:08 PM
07-11-2018 06:08 PM
Networking shows DOWN -- How to bring up?
Hi Everyone,
I'm having some issues getting started with networking. The nodes do not have external access and when connected into the switch, the ping command reports a time out. My architecture is a comware based 180XGc (internal) switch matched to a 4QSFP+ (external, uplink). The uplink (through FGE1/1/1) is connected to a SFP+ port on switch.
When in the moonshot,
> set switch power on sa > connect switch vsp sa
to connect into the switch. Then get an overview of the interface(s),
<HPE>display interface brief
which gives the output,
<HPE>display interface brief Brief information on interfaces in route mode: Link: ADM - administratively down; Stby - standby Protocol: (s) - spoofing Interface Link Protocol Primary IP Description InLoop0 UP UP(s) -- M-GE0/0/0 UP UP -- NULL0 UP UP(s) -- REG0 UP -- -- Brief information on interfaces in bridge mode: Link: ADM - administratively down; Stby - standby Speed: (a) - auto Duplex: (a)/A - auto; H - half; F - full Type: A - access; T - trunk; H - hybrid Interface Link Speed Duplex Type PVID Description FGE1/1/1 DOWN auto A A 1 FGE1/1/2 DOWN auto A A 1 FGE1/1/3 DOWN auto A A 1 FGE1/1/4 DOWN auto A A 1
(output from the nodes cut off)
My thoughts are that maybe the 'Administratively down' status on the link could be it? Like, I may need to bring the interface up? Or else the FGE1/1/1 should be told to operate in a ten gig mode so that it matches the SFP+ port?
I've read quite a few of the manuals learning the comware syntax and also tried editing the config file directly but I'm just not being successful.
Any tips would be greatly greatly appreciated!!
-J
- Mark as New
- Bookmark
- Subscribe
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
08-07-2018 04:04 AM
08-07-2018 04:04 AM
Re: Networking shows DOWN -- How to bring up?
Hi,
Physical layer itself is not up. i.e interface.
Make sure the interface is Up and try to test the connectivity or please post the query to moonshot forum instead of networking.
THanks,
Bala
I work for HPE
Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2019 Hewlett Packard Enterprise Development LP